Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1757
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.
Reference: RBD-1934
Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-1766
Supports 5V/3.3V input Onboard RT9161 faster load the appropriate speed Ideal for noisy power environment Application: DIY project.
Reference: RBD-1966
Tuya Smart Wifi Wireless Natural Gas Leak Detector Gas Sensor Household Combustible LPG Gas Leak Alarm Detector With LCD Display
Reference: RBD-0430
Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD
Reference: RBD-1811
AS5600 Magnetic Induction Angle Measurement Sensor
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-1813
ICM-20948 MEMS Motion Tracking Device Sensor Board 9 Axis
Reference: RBD-2210
Photoelectric switch sensor DC 10-30V power supply Working current: 200mA Induction distance: 5-30cm Response time: 1ms Output form: DC three-wire normally open NPN NO Detection object: Transparent / opaque object
Reference: RBD-2325
Brand: DFRobot
This is a dissolved oxygen sensor kit. A dissolved oxygen meter is used to measure the dissolved oxygen in water, to reflect the water quality. It is widely applied in many water quality applications, such as aquaculture, environment monitoring, natural science, etc. There’s an old saying regarding keeping fish, “Good fish deserves good water”. Good...
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2298
Easy to install with adhesive sticker Detects light levels up to 30,000 LUX Sensitive to changes in light intensity Waterproof for outdoor use Linkage with other smart home devices for automation and control Battery-powered for convenient use
Reference: RBD-2497
Compact size, measuring only 13*13*2.5mm Low power consumption High sensitivity and rapid response recovery Advanced MEMS technology Gas detected: CO Sensitivity: R0(in air) / Rs(in 150ppm CO) ≥ 3 Lifespan: ≥5 years (in air)
Reference: RBD-1913
Onboard LDO Voltage regulator Can be interfaced with 3V3 or 5V Microcontroller. Tap/Double Tap Detection Free-Fall Detection Analog output Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from the motor and other high current electronics Power LED
Reference: RBD-2330
The AS7343 is a 14-channel highly versatile, multi-purpose spectral sensor enabling new consumer, commercial, industrial and laboratory applications. It is optimized for reflective, transmissive and emissive measurements including color matching, fluid or reagent analysis or general spectral reconstruction. The spectral response is defined by individual...
Reference: RBD-2508
The ENS160 is a digital multi-gas sensor specifically designed for indoor air quality testing that optimizes the detection of a wide variety of gases and volatile organic compounds (VOCS), including toluene, hydrogen, ethanol, N02 and ozone. The air quality sensor is used in home and building automation, consumer products, electrical and air purification
Reference: RBD-1919
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-2332
Infrared Photodiode Transmitter 5mm Infrared Photodiode Receiver 5mm
Reference: RBD-2667
MG811 (CO2) Carbon Dioxide Gas Sensor Metal Oxide Sensor Highly sensitive to CO2 Less sensitive to alcohol and CO Analog and digital output options Compatible with Arduino & Raspberry Pi Wide detecting scope
Reference: RBD-2130
9DOF IMU module with compass, acceleration, and gyroscope sensors Captures nine different types of motion or orientation Measures 3-axis gyroscope, triaxial accelerometer, and triaxial magnetic field Power supply: 3-5V (internal low dropout regulator)
Reference: RBD-2341
Operating Voltage: 2.7V ~ 5.5V Power Down Feature Stable Temperature Coefficient Can be directly interfaced with a Microcontroller Compatible with Arduino as well as Raspberry Pi.
Reference: RBD-2729
The SGP41 from Sensirion is an innovative VOC and NOx sensor engineered to serve as a digital smart switch and regulation unit in air treatment systems like air purifiers. Utilizing Sensirion's advanced Gas Index Algorithm, the sensor accurately processes two distinct signals, enabling automatic triggering of air treatment devices for the removal of...
Reference: RBD-2329
The LSM6DS3TR-C is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 0.90 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer.
Reference: RBD-2347
TSL2591 Digital Light Sensor Breakout Module High Dynamic Range Lux IR Infrared Full Spectrum Diodes Detect 3.3V for Arduino
Reference: RBD-2730
The SGP40 is a digital gas sensor designed for easy integration into air purifiers or demand-controlled ventilation systems. Sensirion’s CMOSens® technology offers a complete, easy-to-use sensor system on a single chip featuring a digital I2C interface and a temperature-controlled micro hotplate, providing a humiditycompensated VOC based indoor air...
Reference: RBD-2348
Operating Voltage: 3.3V Supply Voltage: 3.3V The TCS3472 device provides digital return values for red, green, blue (RGB) and bright light sensing Color management is more accurate. The high sensitivity. Wide dynamic range. IR shading filters make the TCS3472 ideal.
Reference: RBD-2448
This module serves to breakout the MMA8452Q chipset, a chip capable of providing 3 axis acceleration readings. The chipset features a 3 axis accelerometer (±2-8g) and an internal dropout regulator to allow the use of 5V and 3.3V supplies. When combined with free libraries it is possible to utilize the chipset's processing power to perform data conversions...
Reference: RBD-2793
Cost-Effective Oxygen Detection Dual Detection Reliable Performance Versatile Outputs Compact & Easy to Use *Not a medical device*
Reference: RBD-2363
This module is based on ISL29125 that is a low power, high sensitivity, RED, GREEN and BLUE color light sensor (RGB) with an I2C (SMBus compatible) interface. Its state-of-the-art photodiode array provides an accurate RGB spectral response and excellent light source to light source variation (LS2LS).
Reference: RBD-2733
GY-50 L3G4200D 3-Axis Gyroscope Sensor Module Three selectable full scales (250/500/2000 dps) I2C and SPI digital output interface avail. Two I2C address you can select by jumpers 16 bit-rate value data output 8-bit temperature data output Wide supply voltage: 2.4 V to 3.6 V Low voltage-compatible IO (1.8 V) Embedded power-down and sleep...
Reference: RBD-2794
All-in-one Oxygen Monitoring: This complete kit combines the OCS-3F ultrasonic sensor with an LCD display and power supply for convenient oxygen concentration and flow rate monitoring. Enhanced User Experience: The large LCD screen displays real-time oxygen concentration (21% - 95.6%), flow rate (up to 20 L/min), and room temperature for clear and easy...