Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0414
A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...
Reference: RBD-0415
Has a signal output instruction When the output valid signal is high, the light goes out The sensitivity is adjustable (fine-tuning) The wide detection range of vibration, no direction With mounting holes, firmware installation is flexible and convenient. RoboticsBD
Reference: RBD-0319
Type K Type. Mounting thread: M6 Temperature Range:0-600°C. RoboticsBD
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-0424
SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-2140
220V Double Bearing DC Motor Dynamo Generator Efficiency: IE 2 Voltage: DC 220V Frequency: 50Hz Power factor: 0.85
Reference: RBD-0572
Operating Power: 60mW/15fpsVGAYUV. Sleeping Mode: <20 uA. Lens Size: 1/6″. Max. Frame Rate: 30fps VGA. Sensitivity: 1.3V / (Lux-sec). dynamic range: 52 dB. Electronic Exposure: 1 to 510 row.
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-0664
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD
Reference: RBD-0666
Crystal: the oscillation frequency of 455. Button: free height is less than 3mm, the force 200-350g, the life of more than 200 000. Photo-detector and preamplifier in one package. Internal filter for PCM frequency. RoboticsBD Improved shielding against EMI. Don’t forget to add CR2025 Battery to your Cart as this remote does not come with a battery
Reference: RBD-1851
Lightweight brushed DC coreless motors Excellent affordable price compared to BLDC motors Compact and lightweight design Rated at 39000 RPM Low noise and low resistance High-speed and low-torque motors
Reference: RBD-2688
Assortment of 75 plastic gears for building and customizing gearboxes in robots, models, toys, and more. Includes various gear types like spur gears, crown gears, worm gears, and pulleys. Offers a wide range of sizes to meet diverse project requirements. Ideal for beginners and hobbyists for creating gear-driven mechanisms.
Reference: RBD-2777
Stall torque: 10kg/cm (4.8v); 12kg/cm (6v) Operating voltage: 4.8 ~ 6.6v Temperature range: 0- 55deg Gear Type: Metal gear Dead band width: 1us servo wire length: 32cm Servo Plug: JR (Fits JR and Futaba)
Reference: RBD-2775
The MG945 360° has the ability to rotate continuously though 360° in both directions. This makes this servo perfect for robotics or even the rotation of camera sliders! Continuous rotation servos are like regular hobby RC servos but modified to offer speed control instead of position control. They're essentially compact, affordable motors with...
Reference: RBD-0687
Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V. Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C). Peak current: 1.12mA. RoboticsBD Operating Pressure: 300 hPa to 1100 hPa. Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.
Reference: RBD-3005
Rated voltage: 12V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0700
Operating Voltage: 3.3V-5.5V Low Power Consumption High Accuracy Small Size
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1018
Dimensions: 75 x 13 x 13 mm (L x W x H) Range: 5 kg Cable Length: 18 cm Fitting ScrewHole Size: M3 Rated output: 1.0 0.1mV / V Nonlinear: 0.05% F.S Hysteresis: 0.0% F.S Repeatability: 0.05% F.S
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1066
Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...
Reference: RBD-1202
3-axis magnetic electronic compass. Precise heading information. Operating Voltage: 3 -5 V DC. Driver Chip: HMC5883L / QMC5883L Communication: I2C protocol. Measuring range: ± 1.3-8 Gauss.Library: https://github.com/keepworking/Mecha_QMC5883Lhttps://www.arduino.cc/reference/en/libraries/qmc5883lcompass/
Reference: RBD-1207
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...
Reference: RBD-1179
Temperature measuring range: 0...100°C Typical Input Voltage:3.3VDC,5VDC Operating Current:60uA Interface: Analog ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase unless you're confident that you can use it successfully.
Reference: RBD-1374
Model: AM2301. Supply voltage: 3.3 ~ 5.2 V DC. Signal output form: Digital signal output. Temperature measurement range: -40 ~ +80 ºC. Temperature measurement precision: ± 0.5ºC Humidity range: 10%~90%RH. Humidity measurement precision: ±3%RH.
Reference: RBD-0551
Weighing Range: 0 ~ 1 kg. Rated Output: 1.0 ± 0.1mV / V. Non Linear Output: ± 0.03% F.S. Input Impedance: 1066 ± 10% Ω. Output Impedance: 1000 ± 10% Ω. Insulation Resistance: 2000 MΩ. RoboticsBD
Reference: RBD-1677
Contact Rating: 10 W. Switching Voltage: 220 V. Switching Current: 0.5 A. Breakdown Voltage: 220 VDC. Carry Current: 1 A. Contact Resistance: 100 mΩ.