Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1400
4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-0981
Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1164
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1266
It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-1349
For Standard LCD 16x2. Press here.For Standard LCD 16x2 with Male Header. Press hereFor Standard LCD 16x2 with Female Header. Press hereFor Standard LCD 16x2 with I2C adapter board soldered. Press here.For Standard LCD 16x2 with White Background. Press here.For Standard LCD 16x2 with Blue Background. Press here. Model: LCD1602 Interface: I2C Interface...
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red
Reference: RBD-1575
Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1815
I/O Isolation for MCUs (Micro Controller Units) Noise Suppression in Switching Circuits Driving Port Signal Voltage: 3.6-24V Output Port Voltage Port: 3.6-30V Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.
Reference: RBD-2075
MQ-2 Smoke Gas Detector Sensor ME084 Module for Arduino Operating Voltage:+5V Preheat Duration:20 s
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-2156
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.
Reference: RBD-2157
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-2220
Good PRINT PACK design, very beautiful. 8 world of the three primary colors (red-green-blue) LED color, scanning control mode. Applicable for various platforms, such as 51 / AVR / AVR / ARM / for Arduino All kinds of platforms.
Reference: RBD-2296
Features:This product is a booster coil production suite, the circuit is simple and reliable, with professional line drawings, electronic research convenience enthusiastsUses: high school science experiment, electronic equipment, negative ion generator, scientific small production. This circuit is generated when the stable high-frequency arc, elevated...
Reference: RBD-2302
Low Standby Current. 1-to-8 Bidirectional Translating Switches. I2C Bus and SMBus Compatible. 5-V Tolerant Inputs. Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II. Note : Product may vary in two variants TCA9548A & PCA9548A
Reference: RBD-2304
This is the 24 LED NeoPixel Ring, a small chainable 86mm outer diameter board equipped with 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and requires 5 V.
Reference: RBD-2306
The 12 Bit RGB LED Ring Module with Integrated Drivers – WS2812B can be used in colourful curtain-up/ flow water/raindrop/jump flash and so on hundreds of lighting effects. There is a single data line with a very timing-specific protocol. It has trichromatic colour for each pixel and can complete 16,777,216 colours of all true colour displays, the...
Reference: RBD-2316
1.Wide Analog Input Voltage Range: +/-5V2.Low “ON” Resistance: 80 ohm (type) at Vcc = 4.5V; 70 ohm (type) at Vcc = 6.0V; 60 ohm (type) at Vcc = 9.0V3.Logic Level Translation: to enable 5V to communicate with +/-5V analog signals4.Board Size: 30 x 19 mm
Reference: RBD-2340
2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module to generate square wave for experiment development. This is used to drive stepping motor drivers' square waves, Generate an adjustable pulse for MCU using, and Generate an adjustable pulse for controlling the relative circuit (PWM adjust lightspeed, etc).
Reference: RBD-2410
Retain the merits of the V4.0 version Laminated design PCB immersion gold processing technology IIC interface Bluetooth module communication interface SD card module communication interface APC220 wireless rf modules communication interface RB URF v1.1 ultrasonic sensors interface 12864 LCD string of line and parallel interface 32 servo controller interface
Reference: RBD-2421
Product name: Humidifier Driver BoardColor: As showVoltage: DV 5VCurrent: 300mAPower: 2WFrequency: 110KHzSize: approx. 46 *20*17mm/1.81*0.79*0.67"