Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-2629
Diameter 3mm and Length 30 (M3 x 30) Round Machine Screw (Countersunk)
Reference: RBD-1157
Wick Width: 3 mm (+/- 2) Length: 1.5 Meter Material: Copper
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-1162
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1325
USB Output: 5V 2.1A / 5V 1A(Dual USB interface). Batteries Type: liquid lithium-ion batteries (18650) 3.7 lithium-ion batteries only. Screen size: 27mm x 17mm. Charging voltage input: 5V-6V 1A. Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
Reference: RBD-0564
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
Reference: RBD-1587
It is a perfect solution for those who want to make custom power cable. This CCTV Camera DC Power Connector will provide a great connection. The internal diameter of the plug: 2.1mm The external diameter of the plug: 5.5mm
Reference: RBD-0990
Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.
Reference: RBD-1098
Interface: I2C Operating Voltage: 3-5VDC Ports: 8-bit Parallel Ports Can be used with Arduino and Raspberry Pi
Reference: RBD-1787
Diameter 3mm and Length 20 (M3 x 20) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1790
Diameter 3mm and Length 16 (M3 x 16) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1791
Diameter 3mm and Length 12 (M3 x 12) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1792
Diameter 3mm and Length 10 (M3 x 10) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1328
Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-2197
Model: 030-2927Motor size : 18.6mm*15.4mm*11.8mm (approx.)Motor shaft diameter: 1.5mm (approx.)Output shaft length: 8.5mm (approx.)
Reference: RBD-1801
Hole Diameter 4mm Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1802
Hole Diameter 5mm Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1805
Hole Diameter 5mm Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1832
Simple & professional appearance for power cabling. Easy camera installation, saves time and provides more secure cable connection. No electrical tape, no splicing, no crimping - only a small screw driver needed.
Reference: RBD-1996
Diameter 3mm and Length 10 (M3 x 10) Round Machine Screw (Countersunk)
Reference: RBD-1997
Diameter 3mm and Length 12 (M3 x 12) Round Head Machine Screw (Countersunk)
Reference: RBD-1998
Diameter 3mm and Length 16 (M3 x 16) Round Head Machine Screw (Countersunk)
Reference: RBD-1999
Diameter 3mm and Length 20 (M3 x 20) Phillips Round Head Machine Screw (Countersunk)
Reference: RBD-2011
Diameter 3mm and Length 8 (M3 x 8) Round Machine Screw
Reference: RBD-2018
Diameter 3mm and Length 6 (M3 x 8) Round Machine Screw
Reference: RBD-2170
Visualize magnetic fields with ease using the field paper Large size of 100mm x 100mm for a clear and detailed view Micro-encapsulated film enables visualization of magnetic fields Suitable for use with any magnet Lightweight and compact for easy handling and storage
Reference: RBD-2178
Mini grabber SMD IC test hook for logic analyzer Retractable hook with 2mm inner spring Perfect for continuity testing of circuit board components Can be used to test IC, repair cell phone, or other mini electronic products Double Dupont plug lead for connecting to logic analyzer or oscilloscope Note: You will receive random color. If you order 2pcs you...
Reference: RBD-1834
PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted