Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-2346
HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0559
Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA 0-5V to 4-20mA Linear Conversion
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-0442
Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. RoboticsBD
Reference: RBD-1816
Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v to 30VDC Compatible With Both 3V and 5V logic
Reference: RBD-1870
Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal. Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm. Has RXD, TXD signal indicator light, monitor send and receive status.
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-1923
Conversion range: 0% -100% PWM to 0-10v voltage PWM signal reception frequency range: 1KHz – 3KHz Operating voltage: 12V – 30V DC Allowable error: 5%
Reference: RBD-0426
Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity
Reference: RBD-2210
Photoelectric switch sensor DC 10-30V power supply Working current: 200mA Induction distance: 5-30cm Response time: 1ms Output form: DC three-wire normally open NPN NO Detection object: Transparent / opaque object
Reference: RBD-2292
Onboard CAN transceiver SN65HVD230 Powered from 3.3V Features ESD protection Connecting MCUs to the CAN network Compatible with PCA82C250
Reference: RBD-0428
Operational Voltage: 3.3V. Ambient Light & RGB Color Sensing. Proximity Sensing. Gesture Detection. Operating Range: 4-8in (10-20cm). I2C Interface (I2C Address: 0x39). RoboticsBD
Reference: RBD-2467
0-150kHz PWM generator in a panel mount enclosure
Reference: RBD-0441
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD
Reference: RBD-0554
VL53L0X 3-in-1 ranging and gesture detection sensor Regulator: 5 to 2.8V range input voltage (output voltage: 2.8V) VL53L0X signal interface level shifter Serial Port PWM Output True distance measurement independent of target size and reflectance Breakout board, easy to integrate into the customer device Allows basic gesture recognition use case. RoboticsBD
Reference: RBD-2677
Operating on a 5V DC power supply with a current consumption of less than 60mA, this 0.28-inch Digital Voltmeter Ammeter is a versatile tool for measuring voltage and current. With a testing range of 0-100V for voltage and 1-100A for current, this meter offers precise measurements with easy readability, even in dim light conditions.
Reference: RBD-0574
3-Axis Magnetoresistive Sensors and ASIC in a 3.0x3.0x0.9mm LCC Surface Mount Package Temperature Compensated Data Output and Temperature Output Automatic Offset Compensation. RoboticsBD
Reference: RBD-2683
XH-M452 DC 12V LED Digital Thermostat Temperature Humidity Control Module The XH-M452 temperature and humidity control module is a versatile and precise solution for temperature and humidity regulation in various applications. With a power supply of DC 12V, this module offers reliable performance and accuracy. Key Specifications: Power supply: DC 12V...
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-2684
100% brand new and high quality. Widely used in street lights, neon lights, bells, radio and television equipment, production equipment, electrical equipment and household appliances automatic control. Built-in high-performance batteries as backup power in case of no electricity can still maintain time display and storage of. Auto timer error correction....
Reference: RBD-2685
Specifications: Color: White Material: ABS Dimensions: 60 x 48 x 32mm Output: 12V Power Consumption: 7.5VA Time Range: 1-168 hours Display: LCD Battery: Built-in 1.2V, 40mA Ambient Temperature: -25°C to 55°C Connection Type: Plug-in CN101A
Reference: RBD-2806
K Type Thermocouple Temperature Sensor 100mm Probe 0‑400℃
Reference: RBD-2845
Waterproof analogue sensor with the high temperature working in the range from -200°C to 420°C. The output is resistance dependent on temperature. Probe length is 200 mm.