- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- Internet of things (IoT)
Jumper Wire Type
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Arduino Ethernet Shield in Bangladesh - With this Ethernet Shield, your Arduino board can be connected to internet- Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket- Web client application to use Arduino as a distributed network sensor- Stackable by accepting prototype shield or any other boards with Arduino compatible interface
Arduino Etherner Shield in Bangladesh The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet.
(Retired) Fully Arduino and Microcontroller Compatible ◾ GSM module: SIM900A ◾ RTC backup battery ◾ A microphone port ◾ A headphone jack ◾ RS232 interface selection ◾ RS232 serial port ◾ lithium battery Interface ◾ power input connector ◾ power LED (blue) ◾ power switch ◾ SIM card Slot ◾ SMA antenna interfaces and supporting small antenna ◾ Power On / Off...
LCD keypad shield for Arduino operates at 5V Includes a 2x16 LCD display and 6 momentary push buttons Use digital pins 4, 5, 6, 7, 8, 9, 10, and analog pin 0 to interface with the LCD Do not use Pin 10 while this shield is connected LCD color may vary (green or blue)
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
(Retired) WiFi Shield V3 PCB Antenna Arduino Shield INTRODUCTION DFRobot WiFi Shield, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy to connect to a home
INTRODUCTION Do you want to do some projects with stepper motors suchas an auto curtain, a XY Plotter, or a 3D printer? Generally, it's not an easy thing todrive stepper motor(s) with Arduino; but with this stepper motor shield, you can easily control 2 stepper motors via just 4 digital I/O’s. This board is
Brand: SparkFun Electronics
Description: The Intel® Edison is an ultra small computing platform that will change the way you look at embedded electronics. Each Edison is packed with a huge amount of tech goodies into a tiny package while still providing the same robust strength of your go-to single board computer.
What's on Board Raspberry Pi GPIO interface : for connecting Raspberry Pi USB TO UART : control the Pi through serial terminal AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer
(Retired) Iduino Yun Shield Compatible with Arduino Leonardo, Uno, Duemilanove, Diecimila and Mega Arduino 3G+Wifi+Ethernet Shield Robotics Bangladesh 3g+ Wifi+ Ethernet + USB+ Openwrt (Linux) Geeetech Latest Iduino Yun Shield board Linux WiFi 3G Ethernet USB for Arduino http://www.geeetech.com/wiki/index.php/Iduino_Yun_Shield
Description: The pcDuino3 is a high performance, cost effective mini PC platform that runs full-featured operating systems such as Ubuntu and Android. In addition to running Linux and Android, the pcDuino3 has support for programming languages such as C, C++, Java, Python, Arduino, and more. You can even use your favorite Arduino shields for added...
32 Channel USB UART Servo Motor Controller Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.
Specification: Module Name: MF522-ED Working current：13—26mA/ DC 3.3V Standby current：10-13mA/DC 3.3V sleeping current：<80uA peak current：<30mA Working frequency：13.56MHz Card reading distance ：0～60mm（mifare1 card） Protocol：SPI data communication speed：Maximum 10Mbit/s
(Retired) This SIM808 all in one Shield is a GSM and GPS Bluetooth all-in-one function module. It is based on the latest GSM/GPS module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation GSM Antenna is included. GPS Antenna is not included. Fully Arduino Compatible (Please download the attach...
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is an highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module.
PN532 NFC RFID Wireless Module V3 User Kits Reader Writer Mode IC S50 Card PCB Attenna I2C IIC SPI HSU For Arduino
NXP PN532 NFC RFID Module V3 Kits Reader Writer Arduino Android Phone M92 NFC is a popular technology in recent years. We often heard this work while smart phone company such as Samsung or HTC introduces their latest high-end phones. Almost all the high-end phone in the market support NFC.
Description: Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be difficult to measure. Luckily, the Pulse Sensor Amped can solve that problem!
Size: 0.96 Resolution: 128X64 Color: Blue, Yellow Viewing angle: greater than 160 degrees Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I / O ports Backlight: OLED self light, no backlight