Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Robotics Bangladesh has the biggest collection of electronics components. We are providing plenty of components to support a variety of applications. If you're looking to build your own circuit boards, then you'll need a collection of electronic components to get the job done.Find out your electronic components at the best price in Robotics Bangladesh with a wide range of products and get hassle free service.
Reference: RBD-1266
It has a nice standard 0.1″x0.1″ prototyping grid with big pads Comes with Stacking headers and plain header, choose whichever you want when soldering together An IC pattern for adding DIP ICs up to 20 pins Power rails down the middle and sides A reset button and an extra general use button Two 3mm general use LEDs, red and green, as well as 2 matching...
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-1400
4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...
Reference: RBD-1592
Led String LED 10M Christmas Light /Wedding/Party Decoration garland AC 110V 220V Outdoor Waterproof Lamp 9 Colors
Reference: RBD-2658
This 1 channel 12V 30A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine. The inputs of 1 Channel 12V 30A Relay Module are isolated to protect any delicate control circuitry. It can be used as a single chip module for appliance...
Reference: RBD-2659
Trigger Voltage: 5VDC Switching Voltage: 250VAC@30A; 30VDC@30A The module can be set high level or low-level trigger by the jumper Note: Relay brand may vary from actual product as our stock rotates.
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-2689
Single side PCB. Reinforced with glass fiber laminate on the core. 330 x 200 x 0.8 mm. Ideal for prototyping. Color: Copper, White Smooth Machine Cut
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0887
Rugged chrome-plated metal pushbutton with red LED ring Ideal for panels up to 1/2" thick Easy installation with a simple drill hole Built-in resistor for LED Supports 3 to 6V for LED operation Momentary pushbutton design
Reference: RBD-0889
Rugged chrome-plated metal pushbutton with blue LED ring Ideal for panels up to 1/2" thick Easy installation with a simple drill hole Built-in resistor for LED Supports 3 to 6V for LED operation Momentary pushbutton design
Reference: RBD-0890
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0891
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-2304
This is the 24 LED NeoPixel Ring, a small chainable 86mm outer diameter board equipped with 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and requires 5 V.
Reference: RBD-0892
Rugged chrome-plated metal pushbutton with red LED ring Latching design for maintaining the switch state Built-in resistor for LED Supports 3 to 6V for LED operation IP65 and IK08 protection ratings Durable stainless steel and chrome-plated brass construction
Reference: RBD-2306
The 12 Bit RGB LED Ring Module with Integrated Drivers – WS2812B can be used in colourful curtain-up/ flow water/raindrop/jump flash and so on hundreds of lighting effects. There is a single data line with a very timing-specific protocol. It has trichromatic colour for each pixel and can complete 16,777,216 colours of all true colour displays, the...
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-2643
Pixel chain - 25x LED 5mm Cool White 25 bright LEDs in cool white color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-2644
Pixel chain - 25x LED 5mm Red 25 bright LEDs in Red color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2645
Pixel chain - 25x LED 5mm Blue 25 bright LEDs in blue color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2646
Pixel chain - 25x LED 5mm Green 25 bright LEDs in Green color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2647
Pixel chain - 25x LED 5mm Yellow 25 bright LEDs in yellow color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-2706
Pixel chain - 25x LED 5mm Purple 25 bright LEDs in purple color Weather-resistant silicone case with IP65 protection Suitable for advertising lighting, inscriptions, decorative elements, etc. Supplied voltage: 12V 120° beam angle Chain length: approximately 3.5 meters
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1326
Outer Diameter: 68 mm. Supply Voltage: DC 4-7V. LED driver chip: WS2812B Communication interface: single wire communication. Send data at speeds of 800Kbps. The color of the light was highly consistent Full-color module, Full-color soft lights a lamp strip
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series