

Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs)Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
1.3d pen
3.Manual
4. 6 Color Filament
5.Pen basement
6.Retail box+Gift box
Design
1. Power hole/feed empty
6. Nib
Reference: 1390
General Specification:Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.
Reference: 1403
Creality Ender-3 3D Printer is a classic DIY 3d printer, the inheritance of Creality Ender-3 3d printer. Integrated structure design, to be the best 3d printer for beginners at affordable prices.
Reference: 1317
Brand: Anycubic
TPU Filament Plastic For 3D Printer 1.75mm 500g/Roll Flexible Color Optional Rubber Consumables Material for RepRap 500g/Roll
Reference: 434
This breakout board for TI’s DRV8825 micro stepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and six micro step resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to...
Reference: 1265
Brand: Anycubic
The Anycubic i3 Mega S is a solid, metal-framed 3D printer that comes mostly assembled. Assembly is easy and takes only a few minutes. It is capable of producing high-quality prints.Technical Specifications· Printing Technology: FDM (Fused Deposition Modeling)· Positioning Accuracy: X/Y 0.0125mm Z 0.002mm· Supported Print Materials: TPU, PLA, ABS,...
Reference: 1316
Brand: Anycubic
3D printer filament ABS 1.75mmSpecification: Material: ABS Filament diameter:1.75/3mm Recommend print temperature :190-230c Recommend print speed:40-90mm/s Density:1.25±0.05g/cm⊃3; 1 Spool filament length:340mPackage dimension:(1.75mm filament) 20*5.8*6.6cm (3.0mm filament) 16*3.2*9.0cmProduct certification:RoHS
Reference: 1404
Get access to Creality first leveling-free 3d printer CR-6 SE. For the most part, accurate 3D printing is the result of a leveled bed. That’s usually a challenging goal, though, because most 3D printers will present nozzle clogging, poor adhesion, and generally unleveled-related issues that compromise the quality of prints. The Creality CR-6 SE 3d printer...
Reference: 1392
PETG Filament Plastic For 3D Printer 1.75mm1KG/Roll Compatible with Anycubic I3 Mega S Temperature: 205-230 °C Bed Temperature: 60-80 °C
Reference: 1375
Brand: Anycubic
Technical Specifications ● Machine: Anycubic Photon Zero ● Technique: LCD-based SLA ● Light Source: 405nm ● XY Res.: 0.1155mm, 854*480p ● Z Axis Res.: 0.01mm ● Layer Res.: 0.01~0.2mm ● Printing Speed: 30mm(H)/hour ● Power: 30W ● Materials: 405nm UV resin ● Machine size: 180mm(L)*195mm(W)*367mm(H) ● Printing Volume: 97mm(L)*54mm(W)*150mm(H) ● Weight: ~4.7kg
Reference: 1311
mDrawBot is a 4-in-1 drawing robot kit, it can be assembled into 4 different drawing robots: mScara, mCar, mSpider and mEggBot.
Reference: 436
Specification: Fully assembled & tested, no soldering required. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. 3D Printer Controller for RAMPS 1.4
Reference: 1386
Brand: Anycubic
The ANYCUBIC resin is most suitable for the Photon /Photon S 3D printer. The light source design, exposure time and other printing parameters of different brands of LCD 3D printers are different.The resin composition ratio of ANYCUBIC designed for the photon is special , it is the most consistent with resin photon print parameter.
Reference: 1227
Object Scanning Device with USB 2.0 Interface / CMOS Sensor
Reference: 1312
XY plotter robot kit is a drawing robot, which is a pen or another instrument can move to digital graphics on flat surfaces. It can also be due to the installation of a laser engraver upgrade packs into a laser engraving device converted.
Reference: 435
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink or forced air flow (it is rated...
Reference: 1379
Nema 23 23HS5628 2.8A Two Phase 6.35mm Shaft Stepper Motor With TB6600 Stepper Motor Driver For CNC Part 3D Printer
Reference: 1391
Flexible TPU Filament Plastic For 3D Printer 1.75mm1KG/Roll Compatible with Anycubic I3 Mega S Temperature: 190-230 °C Bed Temperature: 50-80 °C
Reference: 1315
PLA Filament 1.75mm Plastic 3D Printer 1kg/Roll 28 Colors Optional Rubber Consumables Material for PrintingMaterial: PLA Filament diameter:1.75 Recommend print temperature :190-230 C Recommend print speed:40-90mm/s Density:1.25±0.05g/cm⊃3; 1 Spool filament length:340m
Reference: 565
5 axis CNC Breakout Board with optical coupler For Stepper Motor Driver MACH
1.3d pen
3.Manual
4. 6 Color Filament
5.Pen basement
6.Retail box+Gift box