
Reference: RBD-1354
Jumper Wire Single Medium
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
The TL07xH (TL071H, TL072H, and TL074H) family of devices are the next-generation versions of the industry-standard TL07x (TL071, TL072, and TL074) devices. These devices provide outstanding value for cost-sensitive applications, with features including low offset (1 mV, typical), high slew rate (20 V/μs), and common-mode input to the positive supply. High ESD
General Specification | |
Mounting Type | Through Hole |
Product Series | TL07xx Low-Noise FET-Input Operational Amplifiers |
Weight (gm) | 1 (approx.) |
Shipment Weight | 0.005 kg |
Shipment Dimensions | 3 × 3 × 3 cm |
1 x TL072CP JFET Dual Op-Amp
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing
Reference: RBD-1324
Operating voltage: 2.5V-5.5V Maximum output power: 3W x 2 PCB size is about: length 30mm width 22mm overall height after installed is about 16mm Built with switch Potentiometer, can adjust the volume & control power switch freely! Flexible assembly usage.
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-1750
This is a High Precision Signal Amplifier Board/Voltage Amplifier Module based upon AD620 Instrumentation amplifier IC, Input voltage range: DC 3~12V, the amplification is adjustable to 1.5~1000 times, Adjustable zero to improve accuracy. AD620 Instrumentation Voltage Amplifier Module is used for AC, DC signal amplification. If you give the input in...
Reference: 1818
Single, 36-V, 1-MHz operational amplifier. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation...
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V.
Reference: RBD-1883
IC Name: 74LS83A Package/Case: DIP-16 4-BIT BINARY FULL ADDER WITH FAST CARRY LOW POWER SCHOTTKY
Reference: RBD-1318
Low saturation voltage Over temperature protection High noise immunity Applications: Motor Drive & Control Operating Supply Voltage Up To 46 V Total Dc Current Up To 4 A Low Saturation Voltage Overtemperature Protection
Reference: RBD-1278
Wide supply voltage range from 2.0 V to 6.0 V CMOS low power dissipation High noise immunity Latch-up performance exceeds 100 mA per JESD 78 Class II Level B
Reference: RBD-1658
Dimension: 4×6 CM Quantity: 2 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 6 gm PCB color: Green
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0911
Entry-level digital multimeters Palm Size 2mF capacitance test (UT33A+) Work safely in CAT II 600V environment
Reference: RBD-1620
1uF 100V 10% Orange Drop Capacitors Polyester Flim 100V105K