

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
The Arduino Mega is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller
.
EAGLE files: arduino-mega-reference-design.zip
Schematic: arduino-mega-schematic.pdf
Microcontroller | ATmega2560 |
Operating Voltage | 5V |
Input Voltage (recommended) | 7-12V |
Input Voltage (limits) | 6-20V |
Digital I/O Pins | 54 (of which 15 provide PWM output) |
Analog Input Pins | 16 |
DC Current per I/O Pin | 40 mA |
DC Current for 3.3V Pin | 50 mA |
Flash Memory | 128 KB of which 4 KB used by bootloader |
SRAM | 8 KB |
EEPROM | 4 KB |
Clock Speed | 16 MHz |
The Arduino Mega can be powered via the USB connection or with an external power supply. The power source is selected automatically.
External (non-USB) power can come either from an AC-to-DC adapter (wall-wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive plug into the board's power jack. Leads from a battery can be inserted in the Gnd and Vin pin headers of the POWER connector.
The board can operate on an external supply of 6 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 7 to 12 volts.
The power pins are as follows:
The ATmega1280 has 128 KB of flash memory for storing code (of which 4 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library).
Each of the 54 digital pins on the Mega can be used as an input or output, using pinMode(), digitalWrite(), anddigitalRead() functions. They operate at 5 volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:
The Mega has 16 analog inputs, each of which provide 10 bits of resolution (i.e. 1024 different values). By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using the AREF pin and analogReference() function.
There are a couple of other pins on the board:
Click here to leave a review
Brand: SparkFun Electronics
Documents: Schematic Datasheet Getting Started Guide Galileo Unread Email Counter Galileo Documents Product Page Product Video
Reference: DEV-12856
Description: The pcDuino3 is a high performance, cost effective mini PC platform that runs full-featured operating systems such as Ubuntu and Android. In addition to running Linux and Android, the pcDuino3 has support for programming languages such as C, C++, Java, Python, Arduino, and more. You can even use your favorite Arduino shields for added...
QUICK OVERVIEW USB Type: Type-A to Type-B Weight: 25 gm. Length: 30 cm. Fully compatible with the PC. Aluminum under-mold shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference
Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to Internet of thing (IoT) or consumer electronics field.
It can support a wide range of ATMEL AVR microcontroller. It can work with AVR Studio or WINAVR (GCC) You can Burn Arduino Bootloader. 8pin and 6pin ISP Heaper (Both)
Brand: SparkFun Electronics
Description: The Intel® Edison is an ultra small computing platform that will change the way you look at embedded electronics. Each Edison is packed with a huge amount of tech goodies into a tiny package while still providing the same robust strength of your go-to single board computer.
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
All ESP8266 pins are connected with header12 digital pins1 analog inputIntegrated 0.96″ OLEDMicro USB connectionCompatible with ArduinoCompatible with NodeMCU(Lua for ESP8266)Input Power 5VCompatible for ArduinoCompatible with NodeMCU(Lua for ESP8266)Click the link for more details:https://github.com/squix78/esp8266-oled-ssd1306
QUICK OVERVIEW 131 powerful instructions – Most Single Clock Cycle Execution 32 x 8 general purpose working registers Fully static operation Up to 20MIPS throughput at 20MHz On-chip 2-cycle multiplier Write/erase cycles: 10,000 flash/100,000 EEPROM Optional boot code section with independent lock bits In system programming by on-chip boot program True...
Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language.
ESP-12E CP2102 NodeMcu Lua V2 Wireless Module Wifi Internet of Things (IOT) Development Board Based On ESP8266 Micro USB To TTL
WiDo - Arduino WIFI IoT(Internet Of Things) Node (Arduino Compatible) Wido is an Arduino compatible WIFI IoT Node development board, which integrates with WG1300 WIFI solution. The microcontroller of Wido is ATMEL ATmega32U4.
Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.
Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to Internet of thing (IoT) or consumer electronics field.
Description: Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language.
Reference: Geekcreit™
Arduino Uno R3 is the clone one of the latest version of Arduino Uno with an on-board CH340 usb - serial converter chip. Even there are some little differences with respect to the original one, it is almost the same in terms of usage and software. This provides you a cheaper opportunitiy to get started with Arduino boards. The microcontroller model of...
The Mega Pro Embed CH340G / ATmega2560 board is based on the ATmega2560 microcontroller and the USB-UART adapter CH340. The board is compatible with Arduino Mega 2560.
STM8 development board, minimum system board, core board, STM8S103F3P6
XNUCLEO-F411RE Features Compatible with NUCLEO-F411RE, onboard Cortex-M4 microcontroller STM32F411RET6 Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion Supports mbed, build prototype quickly by mbed SDK...
The A9G development board is a multifunctional development board based on AI Thinker’s A9G GPRS/GSM + GPS/ BDS module. You can use it to verify the basic communication and peripheral functions of A9G module. It has the basic phone/SMS, GPRS networking communications and GPS/BDS dual mode positioning function. There are lithium battery charge management,...
The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328P (Arduino Nano 3.x). It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. Cable Included
The Arduino Mega is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller
.