How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
This is MCP2515 CAN Module TJA1050 Receiver SPI 51 Single Chip Program Routine Arduino with this module, you will find easy to control any CAN Bus device by SPI interface with your MCU, such as Arduino UNO and Compatible with Arduino based micro-controller projects. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Input Supply voltage (V) | 5 |
| Working current (mA) | 5 |
| Communication Rate (Mbps) | 1 |
| Data bits | 8 |
| Crystal oscillator (MHz) | 8 |
| Terminal Resistance (Ω) | 120 |
| Supports | CAN V2.0B |
| Length (mm) | 41 |
| Width (mm) | 28 |
| Height (mm) | 14.5 |
| Weight (gm) | 8 |
| Shipment Weight | 0.012 kg |
| Shipment Dimensions | 6 × 4 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1x MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino .
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino in Bangladesh is BDT 410 You can buy the MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino at best price from our RoboticsBD or visit RoboticsBD Office.
|
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
|
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0120
400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips
Reference: RBD-0661
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-1349
For Standard LCD 16x2. Press here.For Standard LCD 16x2 with Male Header. Press hereFor Standard LCD 16x2 with Female Header. Press hereFor Standard LCD 16x2 with I2C adapter board soldered. Press here.For Standard LCD 16x2 with White Background. Press here.For Standard LCD 16x2 with Blue Background. Press here. Model: LCD1602 Interface: I2C Interface...
Reference: RBD-0377
Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2328
The A7670 series is the LTE Cat 1 module that supports wireless communication modes of LTE-TDD/LTE-FDD/GSM/GPRS/EDGE. It supports a maximum 10Mbps downlink rate and a 5Mbps uplink rate. The A7670 series supports multiple built-in network protocols, which are suitable for main IOT applications such as telematics, surveillance devices, POS, industrial...
Reference: RBD-2243
Wearable e-textile technology. Designed with large sew tabs Button Board
Reference: RBD-2410
Retain the merits of the V4.0 version Laminated design PCB immersion gold processing technology IIC interface Bluetooth module communication interface SD card module communication interface APC220 wireless rf modules communication interface RB URF v1.1 ultrasonic sensors interface 12864 LCD string of line and parallel interface 32 servo controller interface
Reference: RBD-1603
USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.
Reference: RBD-2084
Power supply: 3 – 5V Good sensitivity The output format: Digital switching output (0 and 1) The comparator output signal is clean, good waveform, driving ability, more than 15mA. A fixed bolt holes for easy installation. Using a wide voltage LM393 comparator.
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-1973
Brand: DFRobot
Easy-to-use Low-cost expansion board for micro:bit Leads out all IO ports of micro:bit Specially-designed port for “HuskyLens AI camera”. This board can be used to Provide stable 5V power supply for HuskyLens to make it run steadily in all modes. Silkscreens on the back clearly indicate the functions of all interfaces
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: RBD-0684
CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
Reference: RBD-0396
Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz. RoboticsBD
Reference: RBD-1772
Small size package Local voice Customized voice wake-up/command words Universal Serial Port Protocol Support Chinese and English The number of command words reaches 150
Reference: RBD-2488
Support Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet 10BaseT/100BaseTX Ethernet PHY embedded Auto-Negotiation (Full-duplex and half duplex) Support Auto MDI/MDIX Simultaneously Supports to 4 independent sockets 0.18 µm CMOS technology 3.3V operation with 5V I/O signal tolerance Provide Serial Peripheral Interface (SPI MODE...
Reference: RBD-2120
Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
Reference: RBD-2462
HW-212 is a DC adjustable constant voltage constant current step down power supply module with LCD display.HD display input voltage and output voltage, current, power and display status.Adjustable stable output voltage and current.Set output current to meet the demand.It can be used as ordinary buck power supply module, charger and LED constant current...
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-2083
Operating Voltage : 5v. Temperature measurement range : -55°C to 125°C. Measurement Accuracy : ±0.5°C.
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-2567
Interface between a CAN bus controller and the physical differential lines. Onboard TJA1050 CAN controller interface chip Chip commonly used pin has led, convenient connection to use Pin 5 v to the power supply PCB board size: 22 (mm) x11.5 (mm) Fully compatible with the ISO 11898 standard High speed (up to 1 Mbaud)Note : HW-021 on module working remains...
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)
Reference: RBD-1575
Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-2225
Output SPDT Relay. Header connector for connecting power and trigger voltage. LED indicates relay status. Screw terminal connector for easy relay output connection. Note: Relay brand may vary from actual product as our stock rotates.
Reference: RBD-2317
The is a 4 way navigation switch (north, south, east, west) with a center push. Think of it as a mini joystick. Whilst the pins don’t align perfectly to a 2.54mm grid, it can be made to fit into a breadboard or perfboard by bending the pins.
Reference: RBD-2095
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...
Reference: RBD-0413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card. Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years. Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering...
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2244
Wearable e-textile technology. Designed with large sew tabs Slide Switch
Reference: RBD-1060
Perfectly fit on the extruder Noiseless Performance Very low Current consumption Easy to install and connect.
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0188
Logical light indication: a small light indicate CHO electrical level. Input feature: 5PF,100K Ohm. USB power supply; USB logic analyzer for monitoring, analyzing and debugging digital circuits 8-Channels USB logic analyzer with a 24Mhz sampling frequency Can analyze UART, IIC, and SPI, etc automatically Great for MCU, ARM system and FPGA development...
Reference: RBD-2018
Diameter 3mm and Length 6 (M3 x 8) Round Machine Screw
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-1393
Double row. 2.54mm pitch. 2 x 20 pins. Through-hole mount. 12mm pin length.
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
