
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
The TM1637 4 Bits Digital Tube LED Display Module is an affordable solution for displaying the output data of your Arduino project. Though the data displayed is restricted by numbers still it allows users to display some characters too like A, B, C etc. RoboticsBD
This 7 segment LED Display has 4 digits which are controlled by TM1637 Driver Chip. It requires only two connections to control this TM1637 4 Bits Digital Tube LED Display Module. Also thanks to the I2C Bus you can control it using only 2 wires, leaving more pins available on your Microcontroller to connect other things. RoboticsBD
The module is a 12-foot clock with four common anode tube (0.36 inch) display module for driver IC TM1637, only two signal lines can make the MCU control four 7-segment digital tubes.
There are several modules using this TM1637 chip to form a 4 digit numerical display module. TM1637 has also keyboard input capability but is not used
Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
LED Display module to Arduino
GND – GND
Vcc – 5V
DIO – D2
CLK – D3
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Driver IC | TM1637 |
Input Voltage (V) | 3.3 to 5.5 |
Max. Operating Current (mA) | 30 |
Length (mm) | 42 |
Width (mm) | 24 |
Height (mm) | 12 |
Weight (gm) | 10 |
Shipment Weight | 0.015 kg |
Shipment Dimensions | 5 × 3 × 2 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 4 Bits Digital Tube LED Display Module.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of TM1637 LED Display Module for Arduino in Bangladesh is BDT 120 You can buy the TM1637 LED Display Module for Arduino at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0914
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
Reference: RBD-1107
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness Easy to Use with PCB Mounting as well as on Breadboard
Reference: RBD-1108
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red
Reference: RBD-2323
The WS2812B RGB LED Module is a small module with BIG color. The module has a special LED on board that contains three separate LEDs – red, green, and blue – as well as a smart control IC that can individually drive each LED. Each color has 256 intensity levels which allows the module to produce 24-bit color, or more than 16 million colors. Each module...
Reference: RBD-2340
2 Channel PWM Pulse Frequency Adjustable Duty Cycle Square Wave Rectangular Wave Signal Generator Module to generate square wave for experiment development. This is used to drive stepping motor drivers' square waves, Generate an adjustable pulse for MCU using, and Generate an adjustable pulse for controlling the relative circuit (PWM adjust lightspeed, etc).
Reference: RBD-1408
Type: CJMCU MINI USB AMS1117 MINI USB interface input 5V MINI USB outputs 5V and 3.3V DC power socket interface input 5V – 12V. DC power outlet output (5V label) 5V and 3.3V Weight: 2 gm.
Reference: RBD-2102
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing
Reference: RBD-2042
Model: LilyPad Color: Purple Material: CCL Dimensions: 30 x 30 x 6 (LxWxH) mm. Weight: 3 gm.
Reference: RBD-2240
Wearable e-textile technology. Designed with large sew tabs LED Green Color
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-2243
Wearable e-textile technology. Designed with large sew tabs Button Board
Reference: RBD-2216
Module chip using PCF8951 Module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v) The module integrated photoresistor by AD collection precise value of the ambient light intensity Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition Module integrated 1 channel 0-5V voltage...
Reference: RBD-1929
General-purpose HDMI display, Connecting computers, TV boxes, Microsoft Xbox360, SONY PS4, Nintendo Switch and so on Can be used as Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, Win10 IOT, single-touch, free drive Can be used as PC monitor, support Win7, Win8, Win10 system (No touch Function)
Reference: RBD-2098
Big Microphone Sound Sensor Module Sound Detection Sensor Module High Sensitive Voice Sensor
Reference: RBD-2209
16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms
Reference: RBD-0985
Stackable design, easy to plug into the ARDUINO development board. Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly. 3.3v and 5v dual power output. 3.3v and 5v IO compatible. USB2.0 protocol.
Reference: RBD-2455
2.42" Inch OLED Display SSD1309 12864 SPI Serial Port For Arduino C51 WhiteBrand: No BrandMetal Bracket to protect Display
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: RBD-2225
Output SPDT Relay. Header connector for connecting power and trigger voltage. LED indicates relay status. Screw terminal connector for easy relay output connection. Note: Relay brand may vary from actual product as our stock rotates.
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0990
Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.
Reference: RBD-0699
Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2238
Wearable e-textile technology. Designed with large sew tabs LED Blue Color
Reference: RBD-1916
IC Chip: MAX3232 Operating Voltage: 3.3-5.5V It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU Pre-assembled compact size board Suitable for use with most microcontrollers Operates up to 250 kbit/s
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.
Reference: RBD-2308
This Dual Dc motor driver focuses on high efficiency and can withstand high current load, the maximum current up to 30A.
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-2318
The Speaker module is composed of a power amplifier and a loudspeaker. Sound size can be adjusted by the potentiometer on the circuit board. Enter different frequencies, the speakers produce different tones. Can be carried out by for Arduino encoding and DIY their music box!Product data interfaceusing anti plug,the two sides of the interface are...
Reference: RBD-2465
Uses ILI9341 display and XPT2046 touch SPI controllers
Reference: RBD-1219
Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage Easy to expand the experiment with SD card...
Reference: RBD-1218
Model No.:NX8048T050 Display Type:011R(R:Resitive Touchscreen) Operating Voltage (VDC):4.75 ~ 7 Max. Operating Current (mA):410 Touch Type: Resistive Colors:65K (65536)
Reference: RBD-1202
3-axis magnetic electronic compass. Precise heading information. Operating Voltage: 3 -5 V DC. Driver Chip: HMC5883L. Communication: I2C protocol. Measuring range: ± 1.3-8 Gauss.
Reference: RBD-0353
Driver IC: SSD1306 Support wide voltage: 3.3V-5V DC Communication: IIC Working temperature: -30-80 degrees. RoboticsBD
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Reference: RBD-0767
Input Voltage(Max.) : 5V Resistance: 42 Ω Resonance Frequency: 2048 Hz Body Size : 12 x 8mm Pin Pitch: 6mm External Material: Plastic; Color: Black
Reference: RBD-0040
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-1186
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....