

Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs)Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Chip board ENC28J60-I/SO
The board 25MHZ crystal
The network interface board HR911105A
3.3 V power supply pin
The board size : 56 (mm) x 34 (mm)
Chip board ENC28J60-I/SO
The board 25MHZ crystal
The network interface board HR911105A
3.3 V power supply pin
The board size : 56 (mm) x 34 (mm)
Reference: 397
MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino
Reference: 1381
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to...
Reference: 1037
SIM808 module is a GSM/GPS/BT three-in-one function module. It is based on the latest GSM/GPS/BT module SIM808 from SIMCOM, supports GSM/GPRS Quad-Band network and combines GPS technology for satellite navigation. It has high GPS receive sensitivity with 22 tracking and 66 acquisition receiver channels. Besides, it supports A-GPS that available for...
Reference: 1336
ESP8266 ESP-01S 5V WiFi Relay Module Things Smart Home Remote Control Switch Phone APP ESP01 ESP-01 Wireless WIFI Module (ESP8266 is not included)
Reference: 1367
The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266. RGB full color LED Module KY-009 for Arduino, emits a range of colors by mixing red, green and blue. The amount of each primary color is adjusted using PWM.
Reference: 393
Specification: Brand newColor: as picture showsSize: approx. 34 x 26 x 32mm (L x W x H)Quantity: 1pcPS2 joystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads
Reference: 1603
It is a customized version of the classic ARDUINO UNO R3 board. Full integration of microcontroller Atmel ATmega328 and IC Wi-Fi ESP8266 with 32 MB flash memory, and USB-TTL converter CH340G on one board. All modules can work together or independently. With Cable
Reference: 386
Precision Real Time Clock Module DS3231 AT24C32 I2C With Battery
Reference: 419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: 1575
A two-channel relay module (HCMODU0115) featuring 2x G3MB-202P solid-state relays. This module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller. A resistive type fuse is provided on the module to help protect excessive current draw.
Reference: 702
This is a 5V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .**Relay Brand is different from the picture as per stock
Reference: 334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: 1333
The module has 12 push buttons. You can make usual keypads for enter numbers, symbols, or navigate and selections in the program. There are pull-up resistors of different values for each button. This makes it possible to connect all the 12 keys to taking only one analog port of the microcontroller. The button consists of two parts: a cap, which can be...
Reference: 699
1.8-inch color screen,support 65K color display,display rich colors 128X160 resolution, clear display Using the SPI serial bus, it only takes a few IOs to illuminate the display With SD card slot for convenient function expansion Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms Military-grade process standards,...
Reference: 1331
AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110VGeneral information This is the good old AC Dimmer, but with 2 channels. This one also can control the alternating current voltage in the same way. It can be used with lamps, elements, fans, pumps, air cleaners etc. So it’s the same thing, but twice bigger. In the tutorial, you can...
Reference: 703
SSC-32 32Ch Servo Controller Lynxmotion Compatible
Reference: 564
AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.
Reference: 1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red 8x8 Dot Matrix Module - Cascadable, MAX7219
Reference: 990
XFS5152CE Speech Synthesis Module TTS Voice Module Support Encode Decode Realized English & Chinese Speech
Reference: 270
Brand: Waveshare
What's on BoardRaspberry Pi GPIO interface : for connecting Raspberry Pi USB TO UART : control the Pi through serial terminal AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer
Reference: 948
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
Reference: 684
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.
Reference: 159
LCD keypad shield for Arduino operates at 5V Includes a 2x16 LCD display and 6 momentary push buttons Use digital pins 4, 5, 6, 7, 8, 9, 10, and analog pin 0 to interface with the LCD Do not use Pin 10 while this shield is connected LCD color may vary (green or blue)
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 1349
It is another great blue backlight LCD display. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you will be able to realize data display via only 2 wires. If you already has I2C devices in...
Reference: 550
V3 Kit Voice Recognition Module BoardFor Arduino Compatible Sensor Voice Recognition Module is a compact and easy-control speaking recognition board.This product is a speaker-dependent voice recognition module. It supports up to 80 voice commands in all. Max 7 voice commands could work at the same time. Sample Code & Library and Manual is available...
Reference: 413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD cardReal time clock (RTC) keeps the time going even when the Arduino is unplugged.
Reference: 282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Chip board ENC28J60-I/SO
The board 25MHZ crystal
The network interface board HR911105A
3.3 V power supply pin
The board size : 56 (mm) x 34 (mm)