

Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs)Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Arduino MicroSD Card Module
Reference: 1266
Description This prototyping shield is the best out there, and now is even better with Version R3 – updated for the most compatibility with just about all the Arduinos! It works with UNO, Mega, Leonardo, NG, Diecimila, Duemilanove, and compatible Arduino. Yun’s and Arduino Ethernets have a chunky Ethernet jack that gets in the way of stacking, you can use...
Reference: 353
Size: 0.96 Resolution: 128X64 Color: Blue, Yellow Viewing angle: greater than 160 degrees Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I / O ports Backlight: OLED self light, no backlight
Reference: 915
Overview RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
Reference: 986
4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm
Reference: 334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: 1575
A two-channel relay module (HCMODU0115) featuring 2x G3MB-202P solid-state relays. This module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller. A resistive type fuse is provided on the module to help protect excessive current draw.
Reference: 702
This is a 5V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .**Relay Brand is different from the picture as per stock
Reference: 438
Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)
Reference: 1408
Description: AMS1117 3.3V 5V/3.3V DC Mini USB Power Supply Module 1 MINI USB input: 5V DC 2. DC power input: 5V-12V 3. Output: 5V / 3.3V 4. size: 25 * 25mm Package Include: 1x AMS1117 3.3V 5V/3.3V DC Mini USB Power Supply Module
Reference: 313
Specification: Module Name: MF522-ED Working current:13—26mA/ DC 3.3V Standby current:10-13mA/DC 3.3V sleeping current:<80uA peak current:<30mA Working frequency:13.56MHz Card reading distance :0~60mm(mifare1 card) Protocol:SPI data communication speed:Maximum 10Mbit/s
Reference: 1021
Operating voltage: 2.5V-5.5V, recommended 5VSpeaker Load: 2-8 OhmsInput and Output Connectors: Pins on 0.2" centersSize: 24 x 23 x 105 mm (L x W x H)Net weight: 3g
Reference: 306
32 Channel USB UART Servo Motor Controller Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.
Reference: 1164
This LCD comes with male header already soldered. So you don't have to worry about soldering it. You can straight connect it with the breadboard.
Reference: 1137
The ENC28J60 Ethernet Module uses the Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20MHz.
Reference: 1398
This is a 12V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .**Relay Brand is different from the picture as per stock
Reference: 399
Specification:1. "LIGHT" linked with GND, the backlight to be lit.2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3. Use a 3.3V controller, otherwise the display could be quite vague.
Reference: 1219
Product Description Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring 480X320 resolution, clear display, support for touch function Support 16-bit RGB 65K color display, display rich colors 8-bit parallel bus, faster than serial SPI refresh On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating...
Reference: 189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: 314
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
Reference: 1336
ESP8266 ESP-01S 5V WiFi Relay Module Things Smart Home Remote Control Switch Phone APP ESP01 ESP-01 Wireless WIFI Module (ESP8266 is not included)
Reference: 1337
5V ESP8266 Dual WiFi Relay Module Internet Of Things Smart Home Mobile APP Remote Switch
Reference: 1602
The OTA WeMos D1 CH340 WiFi Development Board ESP8266 ESP-12F is a more Powerful Arduino with WIFI support. This development platform Espressif based on the ESP-8266 is the pins of the Arduino Uno almost compatible and can even be used as some shield modules designed for the classic Arduino Uno. *No Cable
Reference: 393
Specification: Brand newColor: as picture showsSize: approx. 34 x 26 x 32mm (L x W x H)Quantity: 1pcPS2 joystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads
Reference: 1331
AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110VGeneral information This is the good old AC Dimmer, but with 2 channels. This one also can control the alternating current voltage in the same way. It can be used with lamps, elements, fans, pumps, air cleaners etc. So it’s the same thing, but twice bigger. In the tutorial, you can...
Reference: 985
This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module. It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and...
Reference: 348
Description: Heart rate data can be really useful whether you’re designing an exercise routine, studying your activity or anxiety levels or just want your shirt to blink with your heart beat. The problem is that heart rate can be difficult to measure. Luckily, the Pulse Sensor Amped can solve that problem!
Reference: 684
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.
Reference: 1218
Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to Internet of thing (IoT) or consumer electronics field.
Reference: 564
AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.
Arduino MicroSD Card Module