
Reference: RBD-1354
Jumper Wire Single Medium
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
These devices consist of four independent high-gain frequency-compensated operational amplifiers that are designed specifically to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if the difference between the two supplies is 3 V to 32 V (3 V to 26 V for the LM2902), and VCC is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent of the magnitude of the supply voltage.
Note: Supply voltages larger than 32V for single supply and outside the range of ±16V for dual supply can permanently damage the IC
Warnings: This device has limited built-in ESD protection. The leads should be shorted together or device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
General Specification | |
Package/Case | PDIP-14 |
Amplifier Type | General Purpose Amplifier |
Minimum Supply Voltage (V) | 3 |
Maximum Supply Voltage (V) | 32 |
Number of Channel | 4 |
Output Current Per Channel | 40 mA |
Input Bias Current (Ib) | 45 nA |
Gain Bandwidth Product (GBP) | 1.2 MHz |
Input Offset Voltage (Vos) | 7 mV |
Slew Rate (SR) | 0.5 V/us |
CMRR (dB) | 65 ~ 80 |
Voltage Gain (dB) | 100 |
Technology | Bipolar |
Max Dual Supply Voltage | ±16 V |
Min Dual Supply Voltage (V) | ± 1.5 |
Max. Operating Current (mA) | 1.5 |
Operating Temperature Range (°C) | 0 to 70 |
Dimensions (mm) LxWxH | 19.3 x 6.35 x 4.47 |
Shipment Weight | 0.005 kg |
Shipment Dimensions | 3 × 3 × 3 cm |
1 x LM324N Quad Op-Amp
Reference: RBD-1013
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
Reference: RBD-1025
Overload protection on the input and output No latch-up when the common mode range is exceeded Applications: Audio, Communications & Networking, Signal Processing
Reference: RBD-1289
IC 74LS164 8-bit Parallel-Out Serial Shift Register with Asynchronous Clear Package / Case: 14-DIP
Reference: 1818
Single, 36-V, 1-MHz operational amplifier. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation...
Reference: RBD-0925
Hold 4 standard 18650 batteries. Wire Length: 15 cm. Output: 14.8 V. Dimension (Appro.) : 80 x 76 x 18 mm. Weight: 28 gm. High-quality plastic material
Reference: RBD-0364
Reduces the risk of hardware failure due to overheating Low profile, will fit into most cases. Simple, Passive cooling. No need for noisy fans. Perfectly sized for the RPi’s CPU
Reference: RBD-0329
Printing method: Thermal dot printing Printing speed: 50 - 80mm/s Resolution: 8 points/mm, 384 points/line Effective print width: 48mm
Reference: RBD-0756
Very low supply current Photo-detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light
Reference: RBD-0767
Input Voltage(Max.) : 5V Resistance: 42 Ω Resonance Frequency: 2048 Hz Body Size : 12 x 8mm Pin Pitch: 6mm External Material: Plastic; Color: Black
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum
Reference: RBD-1359
100uH (0.1mH) 1/2W ±10% Tolerance Axial Lead Epoxy Coated Color Band Identifier Fixed Inductor
Reference: RBD-0349
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux). Power via USB or External Source or 7-16 v to 5 v (automatic selection). The Onboard, 150 ma 5 v Regulator. Built-in USB and serial were debugging). 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB). 8...
Reference: RBD-0241
Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typica
Reference: RBD-1873
VOLT DIGITAL PANEL METER SMALL (4V-30V)(48X30MM)
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP
Reference: RBD-1153
135 quality jumper Color: red, orange, yellow, green, blue, purple, gray, brown, white. Box size: 165 × 55 × 10 (LxWxH) mm. 140 pcs of 22 AWG solid wires
Reference: RBD-1545
9-40V to 5V 3A Step Down Power Supply Buck Converter Input: 9V-40V DC Output: 5V, 3A DC
Reference: RBD-0762
Cable length: 50 cm One connector crocodile test clip Interface: DC Jack Color: red and black Wire AWG: 1.15mm
Reference: RBD-226
Brand: SparkFun Electronics
Camera Module - pcDuino V3 (2MP)
Reference: RBD-0264
Brand: SparkFun Electronics
Lockitron Mechanical Assembly The Lockitron Mechanical Assembly from SparkFun is a perfect solution for the DIY home automation or Internet of Things (IoT) enthusiast, whether you want to make your life easier by not awkwardly fumbling with keys or add some extra security in your home with three-factor authentication.
Reference: RBD-0763
Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-1768
Power Supply Board for Breadboard This PSU board is designed to fit directly onto a standard breadboard such as our BB400T and BB830. to give 2 power rails, 5V or 3.3V, Rail voltages are switch selectable. It can be powered by 7-12V at the DC socket or 5V via the mini USB socket. Voltage in : 5VDC Via USB or 7-12VDC Max Current : 700mA
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Reference: RBD-1329
Current: 1A; Voltage : AC 220V / 380V Thread Dia(Approx) : 11mm/0.43" Overall Size(Approx) : 14 x 20mm/0.55" x 0.78"(D*L) Weight : 16g; Package Content : 2 x Keylock Switch
Reference: RBD-1846
PCB Mounting Type modular jack for easy PCB mounting. RJ45 Modular PCB Jack Telephone Connector. Easy to soldering, suitable for the standard network RJ45 cable, is used widely in-home or office network systems. 1 pcs
Reference: RBD-1688
The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5V at 5A of load current. The LM1084 pin-out is the same as the Lm317 circuit.
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-1502
28 pins. JDEC compliant. Molded notch for proper orientation. Easy to insert and remove ICs. Ideal for narrow ICs.
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum
Reference: RBD-1056
Operating Voltage: 3 to 6VDC Shaft Diameter: 2 mm Shaft Length: 10mm Weight; 15g
Reference: RBD-0927
Weight: 85 gm. Voltage : 11.1 V. Dimensions : 17 x 34 x 72(mm ). Max Continuous Discharge : 25 C(25 A). Balance Plug : JST-XH. Discharge Plug : XT-60.
Reference: RBD-1591
5mm Round 2 pin Color: ultra-bright standard RGB full color Lens: water clear flat mold
Reference: RBD-0661
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 10 Low Current Consumption High Brightness