- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Home Automation
- Learning Kit
- Arduino Shield & Module
- Robotics Parts
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- CNC & Laser Cutter
- PN junction rectifier diode.
- One direction flow of Current.
- Used for conversion of AC power to DC.
- 1N 4007 is electrically compatible with other rectifier diodes
- Used instead of any of the diode belonging to 1N400X series
Store Pickup Available!
Free Ship Over 5000 BDT
1N4007 is a PN junction rectifier diode. These types of diodes allow only the flow of electrical current in one direction only. So, it can be used for the conversion of AC power to DC. 1N 4007 is electrically compatible with other rectifier diodes and can be used instead of any of the diode belonging to 1N400X series
- Low Forward Voltage Drop
- High Surge Current Capability
|Maximum Repetitive Peak Reverse Voltage (V)||1000|
|Maximum RMS Voltage (V)||700|
|Maximum Average Forward Rectified Current (A)||100%|
|Operating Junction Temperature (°C)||– 50 to + 150|
|Storage condition (℃)||-55 to 150|
|Shipment Weight||0.005 kg|
|Shipment Dimensions||3 × 3 × 3 cm|
1 x 1N4007 Diode
Soldering is required
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit.
Reduces the risk of hardware failure due to overheating Low profile, will fit into most cases. Simple, Passive cooling. No need for noisy fans. Perfectly sized for the RPi’s CPU
Single, 36-V, 1-MHz operational amplifier. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation...
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting.
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)
AC 100~240v or 12V DC input The cables come with a fitted fuse. Microprocessor controlled Li-ion, LiPo, and LiFe capable Input voltage monitoring. (Protects car batteries at the field) Battery break-in and cycling feature Data storage (Store up to 5 packs in memory) Internal resistance checker to see pack health Delta-peak sensitivity Individual cell...
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Up to 480 Mbps data transfer rate. USB Type: Type-A to Mini-B Weight: 15 gm Length: 30 cm Exclusively designed for Arduino boards.
Net Content: 15g Paste Color: Brown Does not create High Smoke Does not create Foul/Bad Smell No Residual Waste High-Quality Soldering Additives & Activators for effective soldering Useful for general purpose soldering, electrical wires, components, and cables etc