- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Home Automation
- Learning Kit
- Arduino Shield & Module
- Soldering Accessories
- Robotics Parts
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Module & Adapter
- Keypad /Touch/ Human Interface
- PLC Cable
- RFID/ NFC
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- CNC & Laser Cutter
- Retired Products
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Thermal Printer Paper - 34'
- Printing method: Thermal dot printing
- Printing speed: 50 - 80mm/s
- Resolution: 8 points/mm, 384 points/line
- Effective print width: 48mm. RoboticsBD
Store Pickup Available!
Free Ship Over 5000 BDT
This is a 34' roll of thermal printing paper for use with our thermal printer. This roll is smaller than you find at most office supply stores so it fits directly into the printer without having to remove any paper from the roll. Simply place it into the printer with the glossy side facing front and you’re ready to print, no ink required! This paper is BPA-free. RoboticsBD
Can be used with QR701 58mm Embedded Receipt MIni Thermal Printer.
|Package weight:||0.036 kg|
|Product Size||6.1 x 3.1 x 5.7 cm|
|Shipment Weight||0.050 kg|
Package Includes :
1 x Thermal Printer Paper - 34'
58mm embedded thermal printer 60mm/s print speed Clear printing high efficiency Direct thermal printing
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC
Operating voltage: 2.5V-5.5V Maximum output power: 3W x 2 PCB size is about: length 30mm width 22mm overall height after installed is about 16mm Built with switch Potentiometer, can adjust the volume & control power switch freely! Flexible assembly usage.
Wide supply voltage ranges Low supply-current drain independent of supply voltage Common-mode input voltage range includes ground, allowing direct sensing near ground Low input bias and offset parameters Internal frequency compensation Common mode input voltage range includes ground, allowing direct sensing near ground Input offset voltage is typical 3mV...
Brand: SparkFun Electronics
Lockitron Mechanical Assembly The Lockitron Mechanical Assembly from SparkFun is a perfect solution for the DIY home automation or Internet of Things (IoT) enthusiast, whether you want to make your life easier by not awkwardly fumbling with keys or add some extra security in your home with three-factor authentication.
Cable length: 50 cm One connector crocodile test clip Interface: DC Jack Color: red and black Wire AWG: 1.15mm
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
L Shape 3.5Mm Right Angle Female To Male Plug Adapter Connector
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
3-Axis Magnetoresistive Sensors and ASIC in a 3.0x3.0x0.9mm LCC Surface Mount Package Temperature Compensated Data Output and Temperature Output Automatic Offset Compensation. RoboticsBD