How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 245
Choose your desire Resistor value from below:
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
The piezo electric emits a high-pitch beep that is sure to capture everyone’s attention! To use them, you’ll need to match the wire colors to the wires from the battery pack.
If the volume is too loud, simply use a piece of tape over the top hole on the buzzer and the volume will substantially lower.
Reference: 925
18650 Battery Holder 4S Compatible Battery: 18650 Cell: 4
Reference: 1189
IR Receiver Diode (5mm) IR receiver diodes can be used in object detection applications like line follower,obstacle detecting robots etc.These were used in our IR Sensor Array.
Reference: 343
Get cold or heat up by simply reversing the polarity, used for numerous applications from CPU coolers to alternate power sources, or even for your own custom car drink warmer/cooler.
Reference: 668
DS1302 Real Time Clock Module (DS1302Z clock chip,32.768KHZ crystal)
Reference: 623
DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A
Reference: 345
ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is an highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module.
Reference: 422
Description: This is a simple four wire cable. Great for jumping from board to board or just about anything else. These cables mate with the connectors listed below. They have bare wires on one end and a 4-pin JST SH connector on the other end with a mating socket. Compatible With: Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL...
Reference: 1501
Dip sockets for all your prototyping needs IC Base sockets 8 pin
Reference: 1359
100uH (0.1mH) 1/2W with ±10% Tolerance, Axial Lead, Epoxy Coated, Color Band Identifier, Fixed Inductor
Reference: 241
Description The Original LM35 series are precision integrated-circuit temperature sensors, with an output voltagelinearly proportional to the Centigrade temperature. Thus the LM35 has an advantage over linear temperature sensors calibrated in ° Kelvin, as the user is not required to subtract a large constant voltage from the output to obtain...
Reference: 227
Description: Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V~6V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
Reference: 1539
EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.
Reference: 189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: 1524
Module Model:LM2596 Buck Converter + Voltmeter Input Voltage: DC 4.0~40V ; Output Voltage: 1.25V~37V; Output Current: 2A(normal and stable), 3A Max Cutting Size: 66mm x 35mm Measure Range:4~40V (for measure accurately, please ensure that the input voltage is more than 4V) Ripple Frequency: About 150Khz; Ripple Peak: About 100mV; Voltage Meter Error: ±0.1V
Reference: 566
RS485 USB-485 Converter Adapter Support Win7 XP Vista Linux Mac OS
Reference: 364
Aluminum Heat Sink With Adhesive for Raspberry Pi 3
Reference: 1153
This set of jumper wires can help you remove the clutter on your breadboard
Reference: 679
MQ-135 module is widely used in air quality control equipments for buildings/offices, are suitable for detecting of NH3,NOx, alcohol, Benzene, smoke,CO2 ,etc
Reference: 1162
15G Solid Rosin Welding Soldering Flux Paste High Purity
Reference: 674
The MQ series of gas sensors use a small heater inside with an electrochemical sensor. They are sensitive to a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino.
Reference: 1069
QUICK OVERVIEW Wheel Outer diameter: 42MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 43 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.
Reference: 687
BMP280 Pressure Sensor Module High Precision Atmospheric Arduino Replace BMP180
