
Reference: 984
Heat Shrink Tube
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: 1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: 31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: 245
Choose your desire Resistor value from below:
Reference: 94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
The next evolution of the rotor revolution is here!! The KK2.1.5 is packing newfound power with updated sensors, memory and header pins.
The next evolution of the rotor revolution is here!! The KK2.1.5 is packing new found power with updated sensors, memory and header pins.
The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1.5 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.
The KK2.1.5 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labeled and the voltage sense line color has been changed to red for easy identification, making installation and connections a snap.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1.5 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.
Specs:
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega644 PA
Gyro/Acc: 6050MPU InvenSense Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.6:
Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
What is a Multi-Rotor Control board you ask?
The HobbyKing KK2.1.5 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.
The HobbyKing KK2.1.5 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega644PA IC via the aileron, elevator, throttle and rudder inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).
** Note: It is all ways recommended to update to the latest software version as part of your initial setup.(this is different than v1.6 for 2.0)
Reference: 300
Arducopter APM 2.8 Flight Controller + Ublox NEO 7M GPS with Compass
Reference: 288
GY-801 Multi-Sensor Board - 3 Axis Gyro -3 Axis Accelerometer - 3 Axis Magnetometer, Barometer, Thermometer
Reference: 1546
APM 2.8 Flight Controller 2.5 2.6 Upgraded Built-in Compass for FPV RC Drone Aircraft is the new APM 2.8 flight controller. The sensors are exactly the same as the APM 2.6 flight controller, however, this has the option to use the built-in compass, or external compass via a jumper. This makes the APM 2.8 ideal for use with multi-copters and rovers.
Reference: 735
168 MHz / 252 MIPS Cortex-M4F14 PWM / Servo outputs (8 with failsafe and manual override, 6 auxiliary, high-power compatible)
Reference: 938
Package Included: 1x Mini OSD Module 1x 4 Pins Cable 1x 6 Pins Cable
Reference: 946
Mini Racing Drones Flight Controller 2bits F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush For QX95 QX90 QX80
Reference: 237
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: 228
Features:Glass Fiber Flight Controller Anti-vibration Set Shock Absorber APM/KK/MWCSpecifications:Color: BlackMaterial: Glass fiberSize: 10 * 8 * 1cm / 3.9 * 3.1 * 0.4inPackage weight: 27g / 1ozSuit for different open source flight controller, like APM 2.5/2.6/2.8, KK, MWC, etc
Reference: 704
Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers...
Reference: 821
NEO 7M GPS with Compass for APM 2.6 / APM2.8 / PiXHawk with GPS Mounting Stand
Reference: 931
XW Power Eagle Lipo 3300mAh 11.1V 3S 25C Lipo Battery (T Plug Connector) Product Advantages: 1. Excellent high discharge rate 2. Extra-low internal impedance 3. Discharge in high-temperature 4. Long cycle life and high quality 5. Easy customized, energy density 6. Low self-discharge etc.
Reference: 217
Product Description Specification: Stall torque: 2.2kg/cm(4.8V )2.5kg/cm(6V)Operating speed: 0.11sec/60degree(4.8v), 0.10sec/60degree(6v)Operating voltage: 4.8-6.0VDead band width: 10usDimension: 23*12.2*29mmWeight: 14g
Reference: 719
FlySky FS-i6 2.4G 6CH AFHDS RC Transmitter With FS-iA6 Receiver Mode 2
Reference: 983
Genuine Small Sun 18650 Lithium Battery 3800mAh High Capacity 3.7V Brand: Small Sun (Genuine) Capacity: 3800 mAh Volt: 3.7 Best For Robotics Project
Reference: 216
Description: Brand: Gemfan Item Name: Carbon Nylon 8045 Propeller Material: carbon nylon Size: 8 x 4.5'' Color: black Weight: 14g per pair Diameter of center bore: 5.0mm Thickness of center: 9.7mmHole size: 5mm with 3mm, 3.17mm and 4mm adapters. Can be reamed to 6mm or 1/4" if needed. Recommended wheelbase: 550mm - 700mm Recommended motor: 800KV - 1100KV...
Reference: 1542
A2212 10T 13T 1400KV Brushless Motor for Drone QUICK OVERVIEW Model: A2212/10T/13T Motor KV: 1400 Max. Efficiency Current: 6-12A No Load Current: 0.7A @10V Current Capacity: 16A/60S LiPO Batteries: 2S-3S
Reference: 824
T Plug Power Distribution Board for RC Quadcopter
The next evolution of the rotor revolution is here!! The KK2.1.5 is packing newfound power with updated sensors, memory and header pins.