- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- Retired Products
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Motor Shield L293D
Motor Shield L293D
Store Pickup Available!
Free Ship Over 5000 BDT
Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. Here is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects.
- 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping.
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, 4.5V to 25V
- Pull down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (10-22AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block to connect external power, for seperate logic/motor supplies
- Tested compatible with Mega, Diecimila, & Duemilanove
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink or forced air flow (it is rated...
Monster Moto Shield uses VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! Voltage max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Thermal Shutdown
Features:Voltage max: 16VMaximum current rating: 30 APractical Continuous Current: 14 ACurrent sensing available to Arduino analog pinMOSFET on-resistance: 19 mΩ (per leg)Maximum PWM frequency: 20 kHzThermal ShutdownUndervoltage and Overvoltage shutdown
This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver IC. This module will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor.
Voltage: 5VDiameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 64Stepper Motor Driver Board with ULN2003A, B, C, D four-phase LED indicates the status of the stepper motor workStepper motor with a standard interface, when used directly pluggable
32 Channel USB UART Servo Motor Controller Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.
SSC-32 32Ch Servo Controller Lynxmotion Compatible
16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685 You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output.
3650 1/10 Scale Brushless Motor 3930KV + 60A Waterproof BEAST Series ESC Motor Feature:4 poles 12 slot Hi-torque motor designCNC machined 6061 T6 windings maxinmizes efficiencyHigh RPM ABEC5 oversize bearingsUniversal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screwsPrecision balanced rotor,smoothness for best reliability and maximum RPM
This breakout board for TI’s DRV8825 micro stepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and six micro step resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to...
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor.
Description: Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V~6V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card Real time clock (RTC) keeps the time going even when the Arduino is unplugged.