- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Motor drive10 Amps
Store Pickup Available!
10 AMP motor controller that can control a DC motor with a digital input. This way if we want to use a microcontroller to turn the motor off or on, we can. There should be one digital input for forwardand one digital input for backward. Additionally the board should have two terminal blocks, one for the motor's power and one for connecting the H-bridge to the motor.
This motor is for only one motor and it can provide 10 amps. It can be use with any Arduino board and also with others its supports PWM.
Voltage: 5VDiameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 64Stepper Motor Driver Board with ULN2003A, B, C, D four-phase LED indicates the status of the stepper motor workStepper motor with a standard interface, when used directly pluggable
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink or forced air flow (it is rated...
This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver IC. This module will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor.
This breakout board for TI’s DRV8825 micro stepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and six micro step resolutions (down to 1/32-step). It operates from 8.2 V to 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to...
16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685 You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output.
The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor.
3650 1/10 Scale Brushless Motor 3930KV + 60A Waterproof BEAST Series ESC Motor Feature:4 poles 12 slot Hi-torque motor designCNC machined 6061 T6 windings maxinmizes efficiencyHigh RPM ABEC5 oversize bearingsUniversal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screwsPrecision balanced rotor,smoothness for best reliability and maximum RPM
Features:Voltage max: 16VMaximum current rating: 30 APractical Continuous Current: 14 ACurrent sensing available to Arduino analog pinMOSFET on-resistance: 19 mΩ (per leg)Maximum PWM frequency: 20 kHzThermal ShutdownUndervoltage and Overvoltage shutdown
32 Channel USB UART Servo Motor Controller Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.
INTRODUCTION Do you want to do some projects with stepper motors suchas an auto curtain, a XY Plotter, or a 3D printer? Generally, it's not an easy thing todrive stepper motor(s) with Arduino; but with this stepper motor shield, you can easily control 2 stepper motors via just 4 digital I/O’s. This board is
Monster Moto Shield uses VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! Voltage max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Thermal Shutdown