How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
This is the DC motor, which can be used in any DIY project or in the science fair project. With an operating voltage range of 3V-9V this motors can be operated using two AA batteries or with a 5V USB power supply. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
| General Specification | |
| Operating Voltage Range | 3 to 9VDC |
| RPM | 25000 (approx.) |
| Shaft Length | 5 mm |
| Shaft Diameter | 2 mm |
| Length (mm) | 40 |
| Width (mm) | 20 |
| Height (mm) | 15 |
| Weight (gm) | 30 |
| Shipment Weight | 0.030 kg |
| Shipment Dimensions | 5 × 3 × 3 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 3v-9v Short Shaft 180 DC motor
Reference: RBD-2185
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm front and rear(approx.) Weight; 19g (approx.)
Reference: RBD-2186
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm (approx.) Weight; 17g (approx.)
Reference: RBD-2187
Operating Voltage: 12 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm (approx.) Weight; 43g (approx.)
Reference: RBD-2188
Operating Voltage: 5 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 7 mm (approx.) Weight; 30g (approx.)
Reference: RBD-2190
Operating Voltage: 1.5 to 3VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 5mm (approx.) Weight; 22.5g (approx.)
Reference: RBD-2191
Sanford AA 3200MAH Battery 1.2V Ni-MH Rechargeable Battery 1 pcs Sanford 1.2V AA 3200mAh Battery
Reference: RBD-0829
Material: Aluminium M3 Screws Adjustable type servo arm Mounting Hole Spacing: 14mm Servo disc diameter: 20mm 25Tooth Weight: 2 gm
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-1379
Nema 23 23HS5628 2.8A Two Phase 6.35mm Shaft Stepper Motor TB6600 Stepper Motor Driver CNC and 3D Printer
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0949
Operating Voltage : 2.5 ~ 6V Operating Current : 130 ~ 220mA Flow Rate : 80 ~ 120 L/H Maximum Lift : 40 ~ 110 mm Outlet Outside Diameter: 7.5 mm Outlet Inside Diameter: 5 mm
Reference: RBD-1390
Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.
Reference: RBD-2189
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) O-Shape Shaft Size 10 x 5mm/ (approx.) Weight; 19g (approx.)
Reference: RBD-1533
Motor Type: NEMA23 Material: Mild Steel(MS). Dimensions: 50x62x64 (LxWxH) mm Mounting Holes Size: 5mm Weight: 90gm.
Reference: RBD-1250
DC 12V 100 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-1975
Brand: DFRobot
Clutch function Electronic Protection Large Torque Stable performance Accurate running angle Easy to install
Reference: RBD-2185
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm front and rear(approx.) Weight; 19g (approx.)
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0715
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-363
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 100 Torque: 35KG.CM
Reference: RBD-0819
17kg large torque. 15 kg·cm (208 oz·in) @6V 17 kg·cm (236 oz·in) @7.4V Full metal gear 270 degree rotation Using high-precision potentiometer with new design Convenient plug-in wire
Reference: RBD-2186
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm (approx.) Weight; 17g (approx.)
Reference: RBD-0390
Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).
Reference: RBD-0936
High-Quality Pump Operating Voltage: 24VDC Flow Rate: 1100GPH Outlet Diameter 19mm
Reference: RBD-0912
Model: 8020 Shaft Size: 1.0 mm Rated Voltage: 3.7 V. Rated RPM: 39000. Wire Length: 6cm Prop. Length: 55
Reference: RBD-2058
Voltage: 12V Rated power: 250W Rated torque: 0.8N.m Rated speed: 2750RPM No loading current: ≤14A Rated current: 20A
Reference: RBD-1114
N20 Micro Gear 12V 100RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-1518
Operating Voltage: DC 4.8-6V Offer 3 modes to check servos or ESC The Manual Mode allows you to turn the knob to different speeds and check the reaction time The Neutral mode makes the servo go back to the neutral point The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible Connect to up to 3 servos...
Reference: RBD-0295
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 9.4kg-cm Stall torque @6.6V : 11kg-cm
Reference: RBD-336
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM
Reference: RBD-2143
DC 12V Water Flow Pump Mini Hydro Generator Turbine Flow Hydraulic Conversion for energy conversion Energy Generators
Reference: RBD-1917
Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
