- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Internet of things (IoT)
- Home Automation
- Learning Kit
- Arduino Shield & Module
- Robotics Parts
- Industrial Shield
- Industrial Component
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Module & Adapter
- PLC Cable
- Tools & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
- CNC & Laser Cutter
5V 1 Channel Solid State Relay (SSR)
- Power supply:5VDC/160mA
- Switching Voltage (VAC):240@2A
- Isolation: Phototriac
Store Pickup Available!
Free Ship Over 5000 BDT
This is a 1 Channel 5V Solid State Relay Module. A solid-state relay (SSR) is just what it sounds like; an IC that acts like a mechanical relay. They allow you to control high-voltage AC loads from lower voltage DC control circuitry. They accomplish this by using infrared light as the ‘contact,’ a solid-state relay is really just an IR LED and a photo Triac sealed up into a little box. Solid-state relays have several advantages over mechanical relays.
A Solid State Relay is similar to 1 Channel 5V Relay Module Solid State High-Level SSR DC Control 250V 2A with Resistive to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan compared to the traditional mechanical Relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
Connection Pin :
- DC+: connected to VCC (Supply power according to relay voltage)
- DC-: connected to GND
- CH1: relay module signal trigger point (Effective high-level trigger)
- 1-channel 2 AMP Solid State Relay board.
- Control 1 load of up to 2 amps each at 240 V AC.
- Good for lighting, Holiday displays, etc.
- Has been assembled, and the electrical test passed.
- Led indicator for each relay.
- Use it to control various appliances and other equipment with a large current.
- It can be controlled directly by a Microcontroller
|Switching Voltage (VAC)||240@2A|
|Shipment Weight||0.03 kg|
|Shipment Dimensions||4 × 3 × 2 cm|
1 x 5V 1 Channel Solid State Relay (SSR)
Low Level Trigger Relay Module Two separate LEDs for On/Off indication of the Relay. Triggering input voltage 3.3V – 5V Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Back EMF protection 2 LEDs to indicate when relays are ON. Works with logic level signals from 3.3V or 5V devices Opto...
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting;
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600
Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock
Model: S7-300 CPU313C-2DP Part No: 6ES7 313-6CE01-0AB0 Made in Germany SIMATIC S7-300, CPU 313C-2DP COMPACT CPU WITH MPI, 16 DI/16 DO, 3 FAST COUNTERS (30 KHZ), INTEGRATED DP INTERFACE, INTEGRATED 24V DC POWER SUPPLY, 32 KBYTE WORKING MEMORY, FRONT CONNECTOR (1 X 40PIN) AND MICRO MEMORY CARD REQUIRED
Model: ET200M IM 153-4 Part No: 6ES7 153-2BA00-0XB0 Made in Germany SIPLUS ET200M IM 153-4 PN IO HF -40 ... +70 GRAD C START UP TEMP -25 DGR C WITH CONFORMAL COATING BASED ON 6ES7153-4BA00-0XB0 . DP, ET 200M INTERFACE FOR MAX. 12 S7-300 MODULES, SUPPORTS FAIL SAFE MODULES, HART MODULES SHARED DEVICE, MEDIUM REDUNDANCY PROTOCOL
For Standard LCD 16x2. Press here.For Standard LCD 16x2 with Male Header. Press hereFor Standard LCD 16x2 with Female Header. Press hereFor Standard LCD 16x2 with I2C adapter board soldered. Press here.For Standard LCD 16x2 with White Background. Press here.For Standard LCD 16x2 with Blue Background. Press here. Model: LCD1602 Interface: I2C Interface...
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch