
Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
This 2WD Mini Round Double-Deck Smart Robot Car Chassis DIY Kit Cool and very easy to assemble robot kit. With this car platform, you can add some micro-controller and sensor modules, and program it to build your own robot car.
This kit comes with Round shape chassis, Motors, wheels and all required assembly parts to build a complete robot car. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Round Plate Diameter | 135 mm |
Square Plate Size | 135×90 mm |
Wheel Size (D x W) mm | 65 x 25 grip |
Motor Type | Dual shaft-Straight, BO motor |
Motor Operating Voltage | 3 to 6V DC |
Motor Rated RPM | No Load Speed (3V) 90RPM +-10% |
Motor Gear reduction Ratio | 0.075 |
Motor Rated Current | No Load Current (3V) Less Than 150mA |
Chassis Material & Color | Acrylic Transparent |
Wheel Material | Plastic with Rubber tyre |
Shipment Weight | 0.45 kg |
Shipment Dimensions | 25 × 15 × 4 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x Round Acrylic Plate
1 x Acrylic Baseboard
2 x 65mm Wheel
2 x Universal Wheel
2 x Gear Motor
4 x “T” mode Fixed Motor Bracket
16 x M3X10mm Screw
8 x M3 Nut
4 x M3X12+6mm Copper Cylinder
4 x M3X30mm two-way Copper Colum.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
The latest price of Mini Round Double Deck Chassis Kit 2WD in Bangladesh is BDT 890 You can buy the Mini Round Double Deck Chassis Kit 2WD at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0009
54 Digital I/O terminals (14 of which have programmable PWM outputs). 16 Analog Inputs. 4 UARTs (hardware serial ports). 16 MHz crystal clock. RoboticsBD Operating voltage: 6 ~ 12v. Dimensions: 110 x 53 x 15 mm.
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-0326
Very handy and simple in assembling/disassembling. RoboticsBD Strong components so as to withstand extreme terrain conditions. Transparent Car Chassis. Attractive design. RoboticsBD
Reference: RBD-1061
Low density: lightweight, low inertia. Capability to absorb shock and vibration as a result of elastic compliance. Ability to operate with minimum or no lubrication, due to inherent lubricity. The relatively low coefficient of friction. Operating Voltage(VDC): 3~12 Shaft Length (mm): 8.5 Shaft Diameter (mm): 5.5 (Double D-type) No Load Current: 40-180mA....
Reference: RBD-1183
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow
Reference: RBD-1601
Smart Robot Chassis Black 2WD DC Motor x2 Comes as a kit Two Wheels Smart Car Chassis Tracking Best for Obstacle Avoidance Robot
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-1256
Brand: SparkFun Electronics
Arduino Compatible Easy to assemble Adjustable gear box angles 2 independent DC motors 2 independent hall-effect encoders Thick rubber tank treads 10Kg/cm stall torque per motor
Reference: RBD-1069
Wheel Outer Diameter: 44MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 18 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.
Reference: RBD-1709
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm
Reference: RBD-1301
Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-0749
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-1253
Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote
Reference: RBD-0578
The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm
Reference: RBD-1112
6DOF Robot Arm Kit DIY robot Degree: 6 degree of freedom Material: Stainless steel
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-1071
Height: 11mm Width : 25mm Material: high-quality plastic
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-1264
Car body Material: Aluminum Alloy Car Wheel: Plastic Car strap: Plastic Color: Blue Input Voltage: 12V Weight: 1.2KG Motor & Tanks Chassis is included. No Electronics Parts
Reference: RBD-1070
Dimensions: 22 x 15 mm (Diameter x Height) Weight: 10 gm Body Case Material: Plastic Ball Material: 304 Stainless Steel Application: for MiniQ robot
Reference: RBD-1707
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 21.6gm
Reference: RBD-1657
Metal Mechanical Robot Arm Claw Remote Control Robotic Paws Steering Gear MG996R Servo Arduino Raspberry pi DIY Smart Robot Functional
Reference: RBD-1252
Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes
Reference: RBD-1601
Smart Robot Chassis Black 2WD DC Motor x2 Comes as a kit Two Wheels Smart Car Chassis Tracking Best for Obstacle Avoidance Robot
Reference: RBD-0360
Durable plastic body 6-AA battery holder included two brushed DC motors with 210 mA free run and 2.4 A stall current at 7.2 V maximum speed of 6 in/s (15 cm/s) at 7.2 V
Reference: RBD-0750
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-0918
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. RoboticsBD Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking.
Reference: RBD-0122
Designed for speed with four-wheel drive capabilities Reduce drag with two-wheel drive configuration N20 Gear Versatile Compact
Reference: RBD-2258
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Black Tire + Blue Rim If you need to purchase single 85mm Wheel. Vist here. Note: Hex coupling not...
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-0796
Three DOF (degree of freedom) leg Can walk in any direction. Maximum torque of 13kg for the legs.
Reference: RBD-0326
Very handy and simple in assembling/disassembling. RoboticsBD Strong components so as to withstand extreme terrain conditions. Transparent Car Chassis. Attractive design. RoboticsBD
Reference: RBD-0820
"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."
Reference: RBD-1708
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-0094
The Arduino Uno R3 High-Quality Edition Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6. The Arduino Uno R3 High-Quality Edition embodies superior craftsmanship and meticulous attention to detail, resulting in...
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-1948
Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-0280
Tie-points: 170 (10×17)Size: 48 x 35 x 10 mm(LxWxH).Use: experimental, testing, robotMatching jumper, diameter 0.8mmPhosphor bronze nickel plated spring clipsAccepts a variety of wire sizes (29-20 the AWG)**1 pcs Random Color
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female