

Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
Reference: RBD-0755
Size: 5mm Color: Green Head Shape: Round Lens Appearance: Transparent
General Specification | |
Brand | Generic |
Motor | Mg996r, MG90 |
Length (mm) | 245 |
Width (mm) | 190 |
Height (mm) | 106 |
Weight (gm) | 757 |
Shipment Weight | 0.8 kg |
Shipment Dimensions | 26.5 × 17.5 × 6 cm |
1 x 6DOF Robot Arm Kit
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0217
Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting;
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-1207
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...
Reference: RBD-0402
Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. Operating Voltage (V): 12 DC
Reference: RBD-1707
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 21.6gm
Reference: RBD-1183
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1682
DC 12V 100 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-0267
Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...
Reference: RBD-0285
Brand: RoboticsBD
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0117
Package Name: Line Following Kit Year: 2021 Arduino Uno L298n motor shield Line Following Sensor 5 Array Breadboard medium Tp4056 with 1 cell holder (Charger)
Reference: RBD-0040
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-1635
Logic control, 5V from Arduino main board Polarity protection for External motor power input 2 fast test buttons for each motor channel Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source) Up to 2A current each channel Pin 4, 5,6,7 are used to drive two DC motor Support PWM speed control Support advance speed control
Reference: RBD-0717
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-1880
Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI
Reference: RBD-0265
Printing method: Thermal dot printing Printing speed: 50 - 80mm/s Resolution: 8 points/mm, 384 points/line Effective print width: 48mm Character set: ASCII, GB2312-80 (Chinese)
Reference: RBD-1337
Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600
Reference: RBD-1363
Dimension: 14.5×6 cm Copper Thickness 1-4 OZ Board Thickness 1.1 mm Board color: Brown
Reference: RBD-0041
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-1399
Operating Voltage: 12V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0905
Bluetooth protocol: Bluetooth Specification v2.0+EDR. Frequency: 2.4GHz ISM band. Modulation: GFSK(Gaussian Frequency Shift Keying). Emission power: =4dBm, Class 2. Sensitivity: =-84dBm at 0.1% BER.
Reference: RBD-1708
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-1530
Monomers Bearing: 30KG Permissible Load: 40KG M8 Thread
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0578
The degree of Freedom (DOF): 2 Paw material: aluminum alloy Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm
Reference: RBD-0956
For hobbyists, robot competitions, kids etc. Size:40cm(H) x 23cm(W) Containing the 17DOF: 1DOF of the head 4DOF of the arm 2DOF of the shoulder 2DOF of the hip 6DOF of the legs 2DOF of the feet
Reference: RBD-0926
Manufacturer: Gravitech Operating Voltage (logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch.
Reference: RBD-0941
High-Quality cable One male and one female connector. Flat 25 cm Servo Lead Extension (Futaba) Quality wire and connectors used. Great for larger planes with servos that experience high loads.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V