

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
Features:
Description: This is the latest version of our Venus GPS board; the smallest, most powerful, and most versatile GPS receiver we carry. It's based on the Venus638FLPx, the successor to the Venus634LPx. The Venus638FLPx outputs standard NMEA-0183 or SkyTraq Binary sentences at a default rate of 9600bps (adjustable to 115200bps), with update rates up to 20Hz! The Venus638FLPx also allows for limited on-chip logging (check out the firmware below), as well as external logging using a SPI flash memory chip (not included).
This board includes a SMA connector to attach an external antenna, headers for 3.3V serial data, NAV (lock) indication, Pulse-Per-Second output, and external Flash support. We've also provided solder jumpers to easily configure the power consumption, boot memory, and backup supply. This board requires a regulated 3.3V supply to operate; at full power the board uses up to 90mA, at reduced power it requires up to 60mA.
Sparkfun made it easy to connect an external battery or super capacitor to the board, to support very fast restarts after power is removed. There are even pads on the bottom of the board for the 0.2F supercap (not included but you can find it in the related items below), which will keep the board hot-startable for up to 7 hours without power!
Note: Sparkfun broken out the pins for the Venus638FLPx's second serial port (RX1,TX1) and I2C interface (SDA,SCL). However, these ports are not used by the stock firmware. SkyTraq offers an SDK allowing the creation of customized firmware; contact them for details.
Features:
Dimensions: 1.15 x 0.7 inches
Documents:
Click here to leave a review
Brand: Waveshare
Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply
85mm Antiskid Shockproof Wheels, Smart Car Robot With Wheel Coupling + Motor Mounting Bracket
Mini 2-Axis platform for camera Weight: 20gsuitable for 9g-12g servos or MG90, MG90S, SG90precision and great appearanceit’s a very stable platform for camera Note no servo is included
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after that period, the 'alarm' pin will go low.
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Specification: Electrical parameters: JSN-SR04T Operating voltage: DC 5V Quiescent current: 5mA Total current work: 30mA Acoustic emission frequency: 40khz Farthest distance: 4.5m Blind: 25cm
17DOF Biped Robot Educational Robot Kit 17 Degrees of Freedom Humanoid / Humanoids Walking Robot Kit
Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.
Specification: Input voltage range:4~38VDC(Note:input voltage not exceeding 38V) Output voltage range:1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%(max) Short circuit protection: yes(limit current 8A).
Digital Line Following Sensor - 8 Array. TCRT 5000 8 Array Line Detect Sensor, Single calibration variable/pot. Easy to Calibrate Optional I2C Mode (Require only 4 Wire) Sample Programming Code is available.
Description: Type K Type. Mounting thread: M6 Temperature Range:0-600°C. Thread Diameter:6mm / 0.23". Internal Insulation:Fibreglass. External Shielding:Metal Shield. Total Length:1M / 39". Fork Terminal Spacing: 3.5mm / 0.13". Color: As Picture Shown. 10mm thread sensor for accurate measurement.
Description: This robotic claw is a step up from the classic. The MKII takes everything you loved about the standard robot claw from DAGU and makes some significant improvements!
Long-distance wireless transmission 3 working modes Working frequency range (433.4-473.0MHz, up to 100 communication channels) Built-in MCU, performing communication with external device through serial port
Brand: DFRobot
This 4WD Chassis is simple yet versatile robot chassis designed specifically for students and hobbyist. Featuring large size chassis plates cut from acrylic and designed with numerous holes and mounting points, providing plenty of space to carry a PCB board and any additional components that you choose. The possibilities are only limited by your...
Makeblock mBot Ranger 3-in-1 educational robot kit for Age 10+
Specifications:Voltage: DC12VCurrent: 0.6AEnergized forms: intermittentUnlocking time: 1SSize: 27x29x18mm (L * W * H)
Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Specifications:- Gain: 2.0dBi-2.5dBi- Standing-wave ratio (SWR): <1.5- Directivity: Omni-directional- Center frequency: 5.8Ghz- Connector: RP-SMA- Diameter of connector: 7.67mm- Length:Transmitter antenna:71mm- Receiver antenna:91mm- Net weight: 12g(Tx/Rx)- Package weight:69 g
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
http://www.lewansoul.com/product/detail-6.html# Included Controller and Arduino Nano The robotic arm is DIY kit, please refer to our 3D animation to assemble the mechanical arm by yourself. Please scan the QR code or access the link inside the package to get all the information. It’s not open resource, please ignore the label on the package.
Features: