XiaoR STM32 Self Balancing Programmable Robot

Reference: 345

ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is an highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module. 

Reference: 654

Male Pin Header Single Row ( Short )

Male Pin Header Single Row  ( (Short) 40 pin set )

Reference: 379

Eachine TS832 RC832 Boscam 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V

Eachine TS832 RC832 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V

Reference: 905

Arduino Bluetooth Module (HC-05)

Arduino Bluetooth Module (HC-05) This serial Bluetooth module can work as either master or slave. This module also includes the baseboard, not only the core board, most functions are pre-set, so only the serial port communication is available but it’s easier to use. It can be used also with Arduino or Microcontroller.

Reference: 1560

DC 9V Charging Step Up Booster Module for 18650 Lithium Battery UPS Voltage Converter Protection

It is a UPS uninterruptible power supply control board. DC 9V Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection

Reference: 315

US-015 Ultrasonic Module Distance Measuring Transducer Sensor

  Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm

Reference: 350

STM32F103C8T6 ARM STM32 Minimum System Development Board Module Arduino

Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.

Reference: 166

XBee 1mW Trace Antenna - Series 1 (802.15.4)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Reference: 1334

TP4056 Li-Ion Battery Charger with Protection

TP4056 Li-Ion Battery Charger with Protection for 3.7V Battery

Reference: 549

Breadboard Power Supply Module 3.3V 5V

Details For plug-in test boards, the 3.3V and 5V power supplies have jumper to adjust the desired power. Supports 9V battery jacks, 6.5 - 12V input power adapter, or power supply.Access via USB via Mini USB cable is small space wasted experiment board.  

Reference: 1540

EL Wire-Blue 3m With Pocket Inverter

EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.

Reference: 1582

TDA7492P Bluetooth 4.2 CSR8635 Bluetooth Receiver Amplifier Audio Board 2x25W for 4/6/8/16 Ohm Speakers Module Parts Component

Features:Using CSR8635 Bluetooth chip, Bluetooth V4.2, high software compatibility.TDA7492 digital amplifier chip, designed to optimize the circuit layout, the sound quality is very good, big powerDIP switches can be adjusted directly after the amp gain more respect and better promote greater damping horn

Reference: 127

Obstacle Avoiding Robot Kit

Obstacle Avoiding Robot Kit

Reference: 150

5mW Adjustable Laser Dot Diode Module

5mW Adjustable Laser Dot Diode Module Features: 1. Output Power: 2-5mW2. Wavelength: 650nm3. Working Voltage: 3v - 5v4 .Laser Shape: Dot5. Working temperature: -10 C-40 C

Reference: 377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Monster Moto Shield uses VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! Voltage max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Thermal Shutdown

Reference: 1650

TS-400 4WD Metal Crawler Tank Chassis

TS-400 4WD Metal Crawler Tank Chassis These Robot Chassis come as unassembled you have to assembled it by yourself.

Reference: 414

Waterproof DS18B20 Digital Thermal Probe or Sensor

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!

Reference: 918

Multifunctional Standard Aluminium Servo Bracket

Aluminum Pan and Tilt for a horizontal surface, unassembled; Pan and Tilt Mount Servo Stand for Robot Clamp Claw; Servo bracket used in the shoulders and knees or other joints of humanoid robots, biped robots etc. Comatible With: MG996R, MG995  

Reference: 208

Brand: SparkFun Electronics

Off-Road Wheels - 120x60mm (2 pack)

Off-Road Wheels - 120x60mm (2 pack)

Reference: 296

Servo Wheel with Thick Rubber Tire

Servo Wheel with Thick Rubber Tire can attach to most standard sized servos and compatible gearbox motors. Compatible Servo: MG996R, MG995   Package: 1x Wheel

Reference: 694

NodeMcu Lua V3

ESP-12E/ ESP-12F CP2102 New Lolin NodeMcu Lua V3 Wireless Module Wifi Internet of Things (IoT) Development Board Based On ESP8266 Micro USB To TTL This is the famous NodeMCU which is based on ESP8266 WiFi SoC. This is version 3 and it is based on ESP-12E or ESP-12F  (An ESP8266 based WiFi module). NodeMCU is also an open-source firmware and development...

Reference: 1069

N20 DC Gear Motor Wheel 3PI miniQ Car wheel Tyre

QUICK OVERVIEW Wheel Outer diameter: 42MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 43 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.

Reference: 399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

Specification:1. "LIGHT" linked with GND, the backlight to be lit.2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3. Use a 3.3V controller, otherwise the display could be quite vague.

Reference: 1330

AC Light Dimmer Module, 1 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

The AC Dimmer is designed to control the alternating current voltage, which can transfer current up to 600V/16А.

Reference: 410

X9C103S Digital Potentiometer Module for Arduino

Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S

Reference: 1354

Jumper Wire Single Medium

Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.

Reference: 1575

5V 2 Channel Solid State Relay (SSR)

A two-channel relay module (HCMODU0115) featuring 2x G3MB-202P solid-state relays. This module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller. A resistive type fuse is provided on the module to help protect excessive current draw.

Reference: 1565

Robotic Arm Edge Kit

The Robotic Arm Edge Kit is a remote-controlled robotic arm kit with five degrees of freedom, a 3.5oz (100g) lifting capacity, and an LED light. Using five motors with gearboxes, the Edge has a 120° wrist motion, a 300° elbow motion, a 180° shoulder motion, a 270° base motion, and a 0-1.77" (0-4.5cm) gripping motion. This Robotic Arm Kit comes as...

Reference: 1070

Ball Caster 3PI N20

Ball Caster 3PI N20 This ball caster can be used as a general-purpose ball caster. QUICK SPECS: Height: 1.5cm Distance between two screw holes: 1.5m Length: 2.2cm Ball Diameter: φ12m

Reference: 102

Fingerprint Scanner - 5V TTL (GT-511C1)

Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.