Reference: RBD-0307

MLX90614 Contactless Temperature Sensor Module For Arduino

Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD

Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-1400

4 Channel 12V Relay Board Module

4-Channel Relay interface board and each one needs 15-20mA Driver Current. Both controlled by 12V and 5V input Voltage. Equipped with high-current relay, AC250V 10A ; DC30V 10A. Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low). Indication LED’s for Relay output...

Reference: RBD-1301

Multi-Chassis - Rescue Platform Complete Kit

Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high

Reference: RBD-0291

Sound Sensor Module for Arduino

Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.

Reference: RBD-0572

VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB W/ I2C Interface Arduino

Operating Power: 60mW/15fpsVGAYUV. Sleeping Mode: <20 uA. Lens Size: 1/6″. Max. Frame Rate: 30fps VGA. Sensitivity: 1.3V / (Lux-sec). dynamic range: 52 dB. Electronic Exposure: 1 to 510 row.

Reference: RBD-1367

RGB Full color LED SMD Module

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver

Reference: RBD-0915

UART EM4100 RFID Card Reader RDM6300

Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design

Reference: RBD-1659

Double Sided FR-4 PCB Prototype Board 5x7cm

Dimension: 5×7 CM Quantity : 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 10 gm PCB color: Green

Reference: RBD-1901

XH-M604 Battery Charger Control Module

 Input Voltage: DC 6-60V Display Accuracy: 0.1V Control Accuracy: 0.1V Output Type: direct output Voltage Tolerance: ±0.1V Apply For:6-60V Lithium Lead-acid battery

Reference: 0031

Jumper Wire 40 Pcs Set 20cm

3 Types Available (Please select from option) 1. Male to Male  2. Male to Female 3. Female-Female

Reference: RBD-0208

Off-Road Wheels - 130x60mm (Pair)

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-1183

Yellow Plastic Mag Wheel Soft Tire

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow

Reference: RBD-0344

Weighing Sensor 24 Bit HX711 Dual-Channel

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-0820

Off-Road Wheels - 130x60mm (Single)

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-0195

Brand: RoboticsBD

25mW Infrared Line Laser Light

25mW Infrared Line Laser Light

Reference: RBD-0274

Brand: Waveshare

Raspberry Pi 5inch Resistive Touch HDMI LCD

5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch :  Raspbian 5 inch HDMI with Touch Download Link    

Reference: RBD-0231

Brand: SparkFun Electronics

Beaglebone Black - Rev C

Sitara AM3358BZCZ100 ARM Cortex-A8 32-Bit RISC microprocessor, up to 1GHz Onboard HDMI to connect directly to TVs and monitors More and faster memory now with 512MB DDR3L 400MHz SDRAM, 4GB eMMC Memory Onboard storage frees up the microSD card slot for greater expansion Support for existing Cape plug-in boards TPS65217C PMIC regulator and one additional...

Reference: RBD-1706

4.7 inch Jumper Wire (Pack of 5)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-1653

12V DC Switching Power Supply Mean Well RS-50-12

Input Voltage: 88~264V/47~63Hz Output Voltage: 12V/4.2A DC Output Power: 50W

Reference: RBD-0337

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Reference: RBD-1844

6.5 inch Jumper Wire (Pack of 2)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-2065

JQ6500 HW-896 V1.2 Voice Sound MP3 Player Module

Play standard mono or stereo MP3 files Control with buttons Serial communications protocol (JQ6500 Arduino Library available). Power supply 4.2V Speaker power 4 ohms / 3 watts

Reference: RBD-0715

High Torque Gear Motor 12V 100RPM 25GA

Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions

Reference: RBD-0565

5 axis CNC Breakout Board with optical coupler For Stepper Motor Driver MACH3

Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software. USB power supply and peripherals power phase are separate to protect computer security. All the signals are to-isolate which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc. Wide input voltage range: 12-24V, and with...

Reference: RBD-0259

2WD Wheel Drive Mobile Robot Platform Chassis

Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....

Reference: RBD-1750

Instrumentation Voltage Amplifier Module AD620

Operating Voltage: 3- 12 VDC Amplification: Adjustable 1.5~1000 times Signal Input Voltage Range: 100µV~300mV Signal Output Range: 100µV~300mV

Reference: RBD-2291

2 Channel PS2 Game Rocker Push Button Module For Arduino

Functional configuration: 2 PS2 game joysticks (2 analog voltages per channel) 1 digital level) 2 independent buttons (original button)   Product Features: The X and Y axes output are two potentiometers, and the twist angle can be read by AD conversion. Press the rocker down to send a touch switch, for digital output, has been pulled up Original Omron...

Reference: RBD-1565

Robotic Arm Edge Kit

MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm

Reference: RBD-0385

MCP23017 I2C 16 Input/Output Port Expander

IC Name: MCP23017 Package/Case: DIP-28