HSM-20G analog temperature & humidity sensor

Reference: RBD-0169

Flex Sensor 2.2"

Flex length: 5.6 cm. Total Length: 2.2″ (7 cm). Life Cycle : >1 million. Height : 0.43mm (0.017″), Flat Resistance: 10K Ohms ±30%. Power Rating: 0.5 Watts.

Reference: RBD-1635

Dual Channel Motor Driver Shield For Arduino

Logic control, 5V from Arduino main board Polarity protection for External motor power input 2 fast test buttons for each motor channel Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source) Up to 2A current each channel Pin 4, 5,6,7 are used to drive two DC motor Support PWM speed control Support  advance speed control

Reference: RBD-180

Brand: SparkFun Electronics

Makey Makey Kit

Description: This is the same product as the Makey Makey Standard Kit. The difference is this version comes in fancy clamshell packaging meant for our distributors that need it. Regular customers are welcome to order, but we want to limit the amount of extra packaging finding its way into the trash heap.

Reference: RBD-0196

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

Reference: 1844

6.5 inch Jumper Wire (Pack of 2)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-0346

PN532 NFC RFID Wireless Module V3 User Kits Reader Writer Mode IC S50 Card PCB Attenna I2C IIC SPI HSU For Arduino

Module Size: 42.7mm x 40.4mm x 4mm Easy to change mode: with a small SMD toggle Switch, it becomes very easy to change among IIC, SPI and HSU modes Longer distance: the reading distance becomes 5~7cm, compared with 4~6 cm of last version Built in PCB Antenna, with 5cm~7cm communication distance On-board level shifter, Standard 5V TTL for I2C and UART,...

Reference: RBD-0703

SSC-32 32Ch Servo Controller Lynxmotion Compatible

Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts

Reference: RBD-0549

Breadboard Power Supply Module 3.3V 5V

Breadboard power supply module, compatible with 5V, 3.3V. Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external...

Reference: RBD-1695

25mW Infrared Line Laser Light

25mW Infrared Line Laser Output RED

Reference: RBD-0905

Arduino Bluetooth Module (HC-05)

Bluetooth protocol: Bluetooth Specification v2.0+EDR. Frequency: 2.4GHz ISM band. Modulation: GFSK(Gaussian Frequency Shift Keying). Emission power: =4dBm, Class 2. Sensitivity: =-84dBm at 0.1% BER.

Reference: RBD-0654

Male Pin Header Single Row ( Short )

Single row. 1.27mm pitch. 1 x 40 pins. Through-hole mount.

Reference: 0031

Jumper Wire 40 Pcs Set

3 Types Available (Please select from option) 1. Male to Male  2. Male to Female 3. Female-Female

Reference: RBD-0120

Breadboard (Medium Size)

400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips

Reference: RBD-0948

ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi

Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V

Reference: RBD-1710

37 GB 6mm Hex coupling for Robot Smart Car Wheel 18 mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 12.6gm

Reference: 0828

Single Axis Servo Bracket

Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...

Reference: RBD-1706

4.7 inch Jumper Wire (Pack of 5)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-1639

12V DC Long-Stroke Linear Actuator 300mm

Operating Voltage: 12 V Self Locking Force: 500N Working temperature: -20ºC to +63ºC Aluminium frame and extension tube Compact Design Built in Limit Switch Low Noise Moisture-proof Surface Long life: A service life of more than 50000 times.

Reference: RBD-0345

ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3)

Reference: RBD-0440

433Mhz Wireless Serial Transceiver Module - 1 Kilometer

433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes.

Reference: RBD-1244

Hiwonder 6DOF Metal Robotic Arm with Controller

Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways

Reference: RBD-1402

NodeMCU ESP8266 Expansion Base Board

The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.

Reference: RBD-1155

3.6V Micro Hydro Generator

Built-in Lipo Charging Circuit Stabilized Voltage Output High Battery Capacity

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue.

Reference: RBD-1582

TDA7492P Bluetooth 4.2 CSR8635 Bluetooth Receiver Amplifier Audio Board 2x25W for 4/6/8/16 Ohm Speakers Module Parts Component

25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection

Reference: RBD-1066

Mini Metal Detector Module

Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.

Reference: RBD-0389

PL2303 USB to TTL Serial Converter (Windows 7 & 10 Compatible)

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0698

ESP8266 ESP-01 Serial WiFi Wireless Adapter Module

On-board level shift circuit Arduino UNO R3 and the compatible board can directly connect to this module; Interface logic voltage: 3.3V / 5V compatible(On-board level shift circuit); Working voltage: 4.5~5.5V (Onboard 3.3V LDO Regulator); Working current: 240mA(MAX).

Reference: RBD-127

Obstacle Avoiding Robot Kit

Obstacle Avoiding Robot Kit