Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
The 4mm(25GA) Hex coupling for Robot Smart Car Wheel 18mm Length is a compact coupling for joining your motor to the smart car wheel. They are mostly seen in smart cars, robotic vehicles or small robots. RoboticsBD
4mm(25GA) Hex Coupling is made from high-quality brass which allows you to connect the shaft of the motor and hub of the wheel. It equips hexagonal socket through which you can connect the hub of the wheel at one end of the coupling. The other hollow end of the coupling is connected to the motor shaft.
They have very simple structure and installation also doesn’t require any special skills. It requires no maintenance except tightening the screws when needed.
It safely transfers the rotating power of your motor shaft to the robotic vehicle wheel. The motors with hole diameter 3 mm and 4 mm are compatible with this 4mm(25GA) Hex coupling of 18mm length. Featured By RoboticsBD.
Product Images are shown for illustrative purposes only and may differ from the actual product.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
Note: The Package does not include any wheel, buy them separately on RoboticsBD
Click here Robot Smart Car Wheel
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
General Specification | |
Material | Brass |
Inner Diameter (ID) (mm) | 4 |
Outer Diameter (OD)(mm) | 11 |
Size of Hex Socket | 14mm (Diagonal) |
Length (mm) | 18 |
Weight(gm) | 13.6 |
Shipment Weight | 0.0136 kg |
Shipment Dimensions | 3 × 2.5 × 2.5 cm |
Please allow 5% measuring deviation due to manual measurement.
RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD RoboticsBD
1 x 4mm(25GA) Hex coupling 18mm long
The latest price of 4mm Motor Shaft Coupling Brass Hex 18mm length in Bangladesh is BDT 190 You can buy the 4mm Motor Shaft Coupling Brass Hex 18mm length at best price from our RoboticsBD or visit RoboticsBD Office.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product. |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-0715
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-0749
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-0750
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-1792
Diameter 3mm and Length 10 (M3 x 10) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1796
Diameter 4mm and Length 10 (M4 x 10) Phillips Flat Head Machine Screw (Countersunk)
Reference: RBD-1880
Voltage: 12V DC RPM:500RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0578
The degree of Freedom (DOF): 2 Paw material: aluminum alloy. RoboticsBD Paw weight: about 68g (without motor) Claws overall length: 108mm (overall maximum length when closed paw) Claws overall width: 98mm (maximum overall width of the paw when open) Paw maximum opening angle: 55mm
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-1682
DC 12V 100 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-2524
DC 12V 200 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current Higher durability
Reference: RBD-0691
Supply voltage: 5V Communication: Serial communication (TTL level) Operating istance: 6-10 meters
Reference: RBD-0133
830 Solder-less Points Ideal for Experimenting With Circuit Design In Labs Compatible with resistance, diodes, transistors, LED’s, Capacitors and other types of electronic components Colored coordinates for easy components placement. Accept a variety of wire sizes 20-29 AWG
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0196
Brand: DFRobot
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
Reference: RBD-1710
Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 12.6gm
Reference: RBD-0122
Designed for speed with four-wheel drive capabilities Reduce drag with two-wheel drive configuration N20 Gear Versatile Compact
Reference: RBD-2513
Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 25 Kg / 55 lb Approximate Pickup Weight: 5 KgEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current through it, and...
Reference: RBD-0440
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD
Reference: RBD-1582
25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection
Reference: RBD-1207
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...
Reference: RBD-2074
Output SPDT Relay. Header connector for connecting power and trigger voltage. Screw terminal connector for easy relay output connection. Note: Relay might be different from the picture as per stock
Reference: RBD-1372
Powerful foot High speed Corrosion-resistant 1 pcs CW, 1 pcs CCW
Reference: RBD-1949
N20 Micro Gear 12V 70RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0235
Brand: SparkFun Electronics
Description: This is a framed graphical LCD 64x128 with LED backlight. This unit is a very clear STN type LCD with a simple command interface. This new module includes the negative voltage circuitry on board!
Reference: RBD-1901
Input Voltage: DC 6-60V Display Accuracy: 0.1V Control Accuracy: 0.1V Output Type: direct output Voltage Tolerance: ±0.1V Apply For:6-60V Lithium Lead-acid battery
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-2003
Servo L Bracket 2mm Hard aluminum Sandblasting Surface Multifunctional Bracket Click here Long U Bracket Click here Short U Bracket Click here L-shaped Servo Bracket Click here Oblique U Servo Bracket Click here U Beam Servo Bracket Click here Humanoid Robot Feet Servo Bracket Click here One Word Frame Servo Bracket Click here Bearing for Servo Motor...
Reference: RBD-0258
Brand: SparkFun Electronics
SparkFun Micro OLED Breakout
Reference: RBD-1398
Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock
Reference: RBD-2163
Built-in encoder Average output up to 420 pulses per revolution The brass faceplate has two mounting holes threaded Long D profile metal output shaft (0.354"/9.0 mm)
Reference: RBD-2321
Drive: 2WD Frame:1.5mm aluminum alloy structure, lightweight and high strength Working voltage: 4.5~6V Wheel Diameter:60mm
Reference: RBD-1659
Dimension: 5×7 CM Quantity : 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 10 gm PCB color: Green
Reference: RBD-2106
40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use
Reference: RBD-1300
Size: 5mm Color: BLUE Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0656
Single row. 2.54mm pitch. 1 x 40 pins. Through-hole mount.
Reference: RBD-1855
Input voltage: 3-40V Output voltage: 1.5-35V(Adjustable) Output current: Rated current is 2A, maximum 3A Switching Frequency: 150KHz Operating temperature:Industrial grade (-40 to +85 ) Conversion efficiency: 92%(highest)
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-1706
The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use
Reference: RBD-2100
Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.
Reference: RBD-1299
Size: 5mm Color: White Head Shape: Round Lens Appearance: Transparent