- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
XBee Pro 63mW PCB Antenna - Series 2B (ZigBee Mesh)
Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Store Pickup Available!
XBee Pro 63mW PCB Antenna - Series 2B (ZigBee Mesh)
Description: This is the XBee XBP24-BZ7PIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules.
Not sure which XBee module or accessory is right for you? Check out our XBee Buying Guide!
Note: If you are looking for a simple point-to-point configuration, you might want to try the Series 1 instead. The Series 2 requires considerable setup and configuration. We highly recommend Building Wireless Sensor Networks as a guide for setting up mesh networks.
Note: Series 1 and Series 2B XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2B modules.
Note: If you are using these outside of the United States, please check with your local laws regarding radio communication.
- 3.3V @ 295mA
- 250kbps Max data rate
- 63mW output (+17dBm)
- 1 mile (1600m) range
- Built-in antenna
- Fully FCC certified
- 6 10-bit ADC input pins
- 8 digital IO pins
- 128-bit encryption
- Local or over-air configuration
- AT or API command set
Powerful High Torque DC Gear Motor with Encoder Voltage: 12V DC RPM:100RPM Diameter: 37mm Shaft length: 15mm Length (excl. shaft): View Photos Shaft diameter: 6mm White and red cord : (+)(-) power cord Yellow and blue cord: For Encoder
Description: his is the LIDAR Lite, a compact high performance optical distance measurement sensor from PulsedLight. The LIDAR Lite is ideal when used in drone, robot, or unmanned vehicle situations where you need a reliable and powerful proximity sensor but don’t possess a lot of space.
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Relay modules suitable for switching of higher voltages and perfect for use with microcontrollers including Arduino, ARM, AVR and PIC. The relays used are rated up to 10A and have NO/NC contacts. Each channel has an LED indicator to show the relay is on.Channels: 4Connects directly to a microcontrollerSwitching Capacity: 10AMaximum Voltage: 250VAC /...
Brand: SparkFun Electronics
Description: This is the LSM9DS0, a versatile motion-sensing system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9dof) from a single IC!
Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!
Description This is a compact mounting bracket ideally designed for N20 micro gear motors. It is made of ABS plastic material and it is designed to fit perfectly to N20 motors. The motor bracket only suitable for N series motor, such as motor N20, N20 geared motors, N20 screw motor, N30 motor. Brief Data: Height: 11mm. Width: 25mm. Material: ABS plastic....
Specification: Input voltage range：4～38VDC(Note:input voltage not exceeding 38V) Output voltage range：1.25-36VDC adjustable Output current: 0-5A, recommended for use in 4.5A. Output power: 75W Working temperature: -40~+85 degrees Operating frequency: 180KHz Efficiency:96%（max) Short circuit protection: yes(limit current 8A).
Can be used with: http://store.roboticsbd.com/robotics-parts/265-thermal-printer-sparkfun-robotics-bangladesh.html Description: This is a 34' roll of thermal printing paper for use with our thermal printer. This roll is smaller than you find at most office supply stores so it fits directly into the printer without having to remove any paper from the roll.
MLX90614 Contactless Temperature Sensor Module For Arduino Compatible Application: Thermal Imaging Camera, Wireless Temparature Measure. Easy to integrateFactory calibrated in wide temperature range:-40…+125°C for sensor temperature and-70…+380°C for object temperature.
Micro USB 5V 1A 18650 TP4056 Lithium Battery Charger Module Charging Board With Protection Dual Functions
You can use LC Metal detector non-contact metal induction detection module as a metal detector. When it approaches any metal, it makes a sound. This is a module specifically designed to detect metal. The module operates by inducing currents in metal objects and responding when it occurs. A nice onboard buzzer signals when it detects something and an...
Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.