Reference: RBD-1534

Planetary Gear Motor PG42-775 42 Gear Box Large

Model:PG42-775 Working volt range:12V. Rated volt:12V No-loading Rotation speed:110-120 Rpm Speed Ratio:91

Reference: RBD-0354

TSL2561 Luminosity & Infrared Light integrating sensor

Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD

Reference: RBD-1649

80mm Mecanum Wheel Omni-directional for Smart Robot with 6mm hubs Package

Color: Black Weight: 44g (each) Inner diameter: 3.3mm Outer wheel diameter: 60mm Thickness: 28mm 2 Left Wheel + 2 Right Wheel and 4 pcs of 6mm hubs   This robot Mecanum wheel is compatible with 37GB Motors 6mm Shaft Compatible Motor:  12V 37GB550 Gear Motor High Torque 100 RPM Heavy Duty High Torque Gear Motor 12V Gear Motor High Torque 300 RPM 12V...

Reference: RBD-1892

14500 Lithium Battery Charger USB Micro-B

Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-0319

K Type Thermocouple Sensor Probe for Temperature Controller

Type K Type.  Mounting thread: M6  Temperature Range:0-600°C. RoboticsBD

Reference: RBD-1656

6V,180rpm Micro DC Geared Motor with Back Shaft

L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft

Reference: RBD-0409

4 Channel 5V Relay Board Module

No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...

Reference: RBD-1893

18650 Lithium Battery Charger USB Micro-B

Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.

Reference: RBD-0100

Robotic Claw - MKII With Metal Servo

Description: This robotic claw is a step up from the classic. The MKII takes everything you loved about the standard robot claw from DAGU and makes some significant improvements! 

Reference: RBD-1019

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell

Charging Voltage: 12.6V-13V Overcharge Voltage Range: 4.25V-4.35V ± 0.05V Overpressure Voltage Range: 2.3V-3.0V ± 0.05V Upper Limit Operating Current: 5A-6A

Reference: RBD-1550

MaKey MaKey - An Invention Kit for Everyone

INVENTION KIT FOR THE 21ST CENTURY Connect the world to your computer Invent Everywhere

Reference: RBD-1639

12V DC Long-Stroke Linear Actuator 300mm

Operating Voltage: 12 V Self Locking Force: 500N Working temperature: -20ºC to +63ºC Aluminium frame and extension tube Compact Design Built in Limit Switch Low Noise Moisture-proof Surface Long life: A service life of more than 50000 times.

Reference: RBD-0288

GY-801 - Multi Sensor Board

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-1254

XiaoR STM32 Self Balancing Programmable Robot

Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct

Reference: RBD-0103

NRF24L01+ 2.4GHz Wireless Transceiver Module

Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications. Built-in hardware CRC error detection, Multipoint communication address control. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode Built-in 2.4Ghz antenna Built-in voltage regulator Standard DIP Pitch...

Reference: RBD-0921

2 Axis Pan Tilt Brackets For Camera/Sensors for Servo SG90S MG90S

PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.

Reference: RBD-1256

Brand: SparkFun Electronics

Rover 5 Robot Platform 2 Motors 2 Encoders

Arduino Compatible Easy to assemble Adjustable gear box angles 2 independent DC motors 2 independent hall-effect encoders Thick rubber tank treads 10Kg/cm stall torque per motor

Reference: RBD-1252

Makeblock mBot Ranger 3-in-1 educational robot kit

Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes

Reference: RBD-0905

Arduino Bluetooth Module HC-05

Bluetooth protocol: Bluetooth Specification v2.0+EDR. Frequency: 2.4GHz ISM band. Modulation: GFSK(Gaussian Frequency Shift Keying). Emission power: =4dBm, Class 2. Sensitivity: =-84dBm at 0.1% BER. RoboticsBD

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-0040

Arduino Bluetooth Module HC-06

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-1601

Smart Robot Chassis Kit Black 2WD

Smart Robot Chassis  Black 2WD DC Motor x2 Comes as a kit  Two Wheels Smart Car Chassis Tracking Best for Obstacle Avoidance Robot

Reference: RBD-1336

ESP8266 5V WIFI Relay Smart Home Remote Control Switch

Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...

Reference: RBD-1753

INMP441 Omnidirectional Microphone Module

Digital I2S interface with high precision 24-bit data High signal to noise ratio is 61 dBA High sensitivity – 26 dBFS Stable frequency response from 60 Hz to 15 kHz Low power consumption: low current consumption 1.4 mA High PSR: -75 dBFS

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-0280

Mini Breadboard

Tie-points: 170 (10×17)Size: 48 x 35 x 10 mm(LxWxH).Use: experimental, testing, robotMatching jumper, diameter 0.8mmPhosphor bronze nickel plated spring clipsAccepts a variety of wire sizes (29-20 the AWG)**1 pcs Random Color

Reference: RBD-1402

NodeMCU ESP8266 Expansion Base Board

The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.

Reference: RBD-1844

6.5 inch Jumper Wire (Pack of 2)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-1582

TDA7492P Bluetooth 4.2 CSR8635 Bluetooth Receiver Amplifier Audio Board 2x25W for 4/6/8/16 Ohm Speakers Module Parts Component

25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection

Reference: RBD-1894

Smart Steering Robot Car Chassis

Very handy and simple in assembling/disassembling. Strong components so as to withstand extreme terrain conditions. Transparent Car Chassis. Attractive design. Smart Steering Robot Car Chassis