• How to Place an Order

  • bKash Payment Method

  • Request for Quotation/ International Sourcing

Arduino Uno R3

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.

Price BDT 399
More
In Stock

BreadBoard

Solderless Large BreadboardA breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard). Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary...

Price BDT 95
More
In-Stock
All best sellers
EasyDriver - Stepper Motor Driver
  • EasyDriver - Stepper Motor Driver
  • EasyDriver - Stepper Motor Driver
  • EasyDriver - Stepper Motor Driver
  • EasyDriver - Stepper Motor Driver

EasyDriver - Stepper Motor Driver

BDT 1,100
rating No review at the moment
Quantity
Pre-Order

The minimum purchase order quantity for the product is 2.

  • Store Pickup Available! Store Pickup Available!
  • Shipping Available Shipping Available
Description
Description: The EasyDriver is a simple to use stepper motor driver, compatible 
with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you 
solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to 30V supply 
to power the motor and can power any voltage of stepper motor. The EasyDriver 
has an on board voltage regulator for the digital interface that can be set to 5V or 
3.3V. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision 
motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, 
or 8 wire stepper motors.
 
This EasyDriver V4.5 has been co-designed with Brian Schmalz. It provides much more 
flexibility and control over your stepper motor, when compared to older versions. The 
microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments 
to the microstepping resolution. The sleep and enable pins are also broken out for further
control.
 
Note: Do not connect or disconnect a motor while the driver is energized. This will cause 
permanent damage to the A3967 IC.
 
Note: This product is a collaboration with Brian Schmalz. A portion of each sales goes 
back to them for product support and continued development.
 
Features:
  • A3967 Microstepping Driver
  • MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter 
       and eighth steps (defaults to eighth)
  • Compatible with 4, 6, and 8 wire stepper motors of any voltage
  • Adjustable current control from 150mA/phase to 700mA/phase
  • Power supply range from 6V to 30V. The higher the voltage, the higher the torque at high speeds

Documents:
Product Details

Click here to leave a review

30 other products in the same category:

Arduino GSM / GPRS SIM900 Shield

Details: The GPRS Shield is based on SIM900  module from SIMCOM and compatible with  Arduino and its clones. The GPRS Shield  provides you a way to communicate using  the GSM cell phone network.

Price BDT 2,200
More
There are not enough products in stock

Leap Motion Controller

The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible  speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,

Price BDT 10,000
More
Pre-Order

Brand: SparkFun Electronics

LIDAR-Lite v3

Features: Range: 0-40m Laser Emitter Accuracy: +/- 2.5cm at distances greater than 1m Power: 4.75–5V DC; 6V Max Current Consumption: 105ma idle; 130ma continuous Rep Rate: 1–500Hz Laser Wave Length/Peak Power: 905nm/1.3 watts Beam Divergence: 4 m Radian x 2 m Radian Optical Aperture: 12.5mm Interface: I2C or PWM

Price BDT 19,500
More
Pre-Order

X9C103S Digital Potentiometer Module for Arduino

Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S

Price BDT 500
More
In-Stock

L298N H-Bridge Dual Motor Driver, Stepper Motor Driver

This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver IC. This module will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor.

Price BDT 150
More
In Stock

Mini Breadboard

Description: This black Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple circuits; They’re also great for breaking out DIP package ICs to jumper wires! If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board...

Price BDT 50
More
In-Stock

TowerPro MG90s – Micro Metal Servo

Product Description Specification: Stall torque: 2.2kg/cm(4.8V )2.5kg/cm(6V)Operating speed: 0.11sec/60degree(4.8v), 0.10sec/60degree(6v)Operating voltage: 4.8-6.0VDead band width: 10usDimension: 23*12.2*29mmWeight: 14g

Price BDT 299
More
In-Stock

AMG8833 IR Thermal Camera Breakout (Adafruit Compatible)

Add heat-vision to your project and with an AMG8833 Grid-EYE Breakout! This sensor from Panasonic is an 8x8 array of IR thermal sensors. When connected to your microcontroller (or raspberry Pi) it will return an array of 64 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy...

Price BDT 8,550
More
In-Stock

Weighing Sensor 24 Bit HX711 Dual-Channel

Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. 

Price BDT 600
More
In-Stock

Follow us on Facebook