5.8GHz Circular Polarized Mushroom Antenna RP-SMA Set Tx/Rx for FPV Multicopter

Reference: 1710

37 GB 6mm Hex coupling for Robot Smart Car Wheel 18 mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 50gm

Reference: RBD-314

Double-ended 50cm Cable Crocodile Clips

 Double-ended 50cm Cable  Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.

Reference: RBD-1250

Heavy Duty High Torque Gear Motor

37GB-550 Gear Reducer Motor DC 12V 100 RPM Geared Motor High Torque 16.0 Kg.cm (Approximate Torque) 

Reference: RBD-311

YF-S201 Hall Effect Water Flow Meter / Sensor

Features: Model: YF-S201 Sensor Type: Hall effect Working Voltage: 5 to 18V DC (min tested working voltage 4.5V) Max current draw: 15mA @ 5V Output Type: 5V TTL Working Flow Rate: 1 to 30 Liters/Minute Working Temperature range: -25 to +80℃ Working Humidity Range: 35%-80% RH Accuracy: ±10%

Reference: 1708

25 GA 6mm Hex coupling for Robot Smart Car Wheel 18 mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 50gm

Reference: RBD-573

DC 5V Stepper Motor + ULN2003 Driver Board (28BYJ-48) for Arduino

Voltage: 5VDiameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 64Stepper Motor Driver Board with ULN2003A, B, C, D four-phase LED indicates the status of the stepper motor workStepper motor with a standard interface, when used directly pluggable

Reference: RBD-1019

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell BMS Protection Board (20A, 3S) Battery Not Included

Reference: RBD-562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator Input voltage: DC 3 V to 6 VInput current: 2 A - 5 AHigh-pressure type: the type of pulse currentOutput voltage: 400000 v(Please pay attention to safety)High-pressure discharge distance between 10 mm - 20 mmThe output high voltage wire length: 100 mm

Reference: RBD-259

Arduino 2 Wheel Drive Mobile Robot Platform Chassis

Features: Model: HC-1 Quantity: 1 Color: Transparent + Yellow Material: Acrylic Working voltage: 3~12V RPM: 120 (Under 3V) Gear motor deceleration indicator Chassis made from acrylic material With installation holes, easy to use Great for DIY project Dimensions: 7.72 in x 4.13 in x 0.12 in (19.6 cm x 10.5 cm x 0.3 cm) Weight: 14.29 oz (405 g)

Reference: RBD-306

Torobot 32 Channel USB UART Servo Motor Controller

32 Channel USB UART Servo Motor Controller  Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.

Reference: RBD-377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Monster Moto Shield uses VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! Voltage max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Thermal Shutdown

Reference: RBD-402

3×4 Flexible Keypad

This keypad has 12 buttons, arranged in a 3×4 grid. It’s made of a thin, flexible membrane material  The keys are connected into a matrix, so you only need 7 microcontroller pins (3-columns and 4-rows) to connect the key pad.

Reference: RBD-1301

Multi Chassis Tank Stair Climber

Multi Chassis Kit Come as Ready to Run with Electronics, Battery & Joystick Controller It is already assembled and you just have to charge the battery using the provided charger and this tank is ready to go! 1x MultiChassis Tank with Battery and Electronics 1x Charger 1x Joystick Controller The battery capacity is 2S 7.3V 1430mAh

Reference: RBD-396

Ultrasonic Transducer Waterproof Distance Measuring Sensor Module

Specification: Electrical parameters: JSN-SR04T Operating voltage: DC 5V Quiescent current: 5mA Total current work: 30mA Acoustic emission frequency: 40khz Farthest distance: 4.5m Blind: 25cm 

Reference: RBD-369

Brand: SparkFun Electronics

XBee Pro 63mW RPSMA - Series 2B (ZigBee Mesh)

Features:   3.3V @ 295mA 250kbps Max data rate 63mW output (+17dBm) 1 mile (1600m) range RPSMA connector Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set External Antenna Required

Reference: RBD-196

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

Reference: 1706

4.7 inch Jumper Wire (Pack of 5)

These 4.7" (12 cm) long wires are suitable for a breadboard

Reference: RBD-828

Single Axis Servo Bracket

Robot Uniaxial Steering Gear Servo Bracket Metal Stent Bipedal Robot Manipulator DIY accessories -Black

Reference: RBD-282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-270

Brand: Waveshare

Raspberry Pi 3 Robot Shield Expansion Board Pioneer 600

What's on Board Raspberry Pi GPIO interface : for connecting Raspberry Pi USB TO UART : control the Pi through serial terminal AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer

Reference: RBD-742

Motor Driver 43A BTS7960

Motor Driver 43A BTS7960

Reference: RBD-349

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

Digispark USB Development Board The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when...

Reference: RBD-1538

EL Wire-Green 3m With Pocket Inverter

EL wire is a thin copper wire coated in a phosphor that glows a 360 degree unbroken light when an alternating current is applied to it. It is bendable as a thin neon tube which makes it ideal for flexible decoration. It is great for car decoration, parties, camping and so on.

Reference: RBD-274

Brand: Waveshare

Raspberry Pi 5inch Resistive Touch HDMI LCD

5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch :  Raspbian 5 inch HDMI with Touch Download Link    

Reference: RBD-1541

37 In 1 Sensor Module Board Set Kit For Arduino with Box

37 IN 1 BOX Sensor Kits /37 SENSOR KIT For Arduino with Plastic Box

Reference: RBD-411

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino

Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...

Reference: RBD-684

Motor Driver - Dual TB6612FNG (1A)

The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.

Reference: RBD-159

LCD Keypad Shield for Arduino

LCD keypad shield for Arduino operates at 5V Includes a 2x16 LCD display and 6 momentary push buttons Use digital pins 4, 5, 6, 7, 8, 9, 10, and analog pin 0 to interface with the LCD Do not use Pin 10 while this shield is connected LCD color may vary (green or blue)

Reference: RBD-291

Sound Sensor Module for Arduino

Sound Sensor Module for Arduino

Reference: RBD-920

Ultrasonic Sensor Acrylic Mounting Bracket

  Ultrasonic Sensor Acrylic Mounting Bracket Robotics Bangladesh