Double-ended 50cm Cable Crocodile Clips

Reference: RBD-0041

Smart Speed Detecting Sensor for Arduino

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-1301

Multi Chassis Tank Stair Climber

Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high

Reference: RBD-0411

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino

Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP

Reference: RBD-282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: RBD-1244

Hiwonder 6DOF Metal Robotic Arm with Controller

Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways

Reference: RBD-0270

Raspberry Pi 3 Robot Shield Expansion Board Pioneer 600

AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer CP2102 : USB TO UART converter PCF8591 : 8-bit AD/DA converter, I2C interface

Reference: RBD-1332

I2C Graphic 128x64 LCD Adapter

Adapter: Graphic 128x64 Communication: i2c 

Reference: RBD-0020

Mini Servo SG90

Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm

Reference: RBD-1183

Yellow Plastic Mag Wheel Soft Tyre

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Yellow

Reference: RBD-0120

Breadboard (Medium Size)

400 tie points 2 Power lanes, Total 100 tie points in power lanes 1 Double strip, Total 300 tie points Perfect for Arduino shield prototyping and testing Plastic housing, metal contact clips

Reference: RBD-0573

DC 5V Stepper Motor + ULN2003 Driver Board (28BYJ-48) for Arduino

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: 1810

L293D Shield for NodeMCU V2

This shield is designed for the NodeMCU V2 (narrow width), it comes with L293D motor driver and breakout the GPIO to headers for easy access when connecting to various sensor modules. With the L293D, this shield supports the control of  two (2) brush motor, start, stop, brake, direction and also speed. The shield also extends the GPIO of NodeMCU to header...

Reference: RBD-0015

Motor Shield L293D

2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...

Reference: RBD-127

Obstacle Avoiding Robot Kit

Obstacle Avoiding Robot Kit

Reference: 1353

Jumper Wire Single Long

Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.

Reference: RBD-99

Multi Chassis Tank Rescue Version Robot Platform

This is the Multi-Chassis Rescue Platform, an easy to assemble and use robot chassis kit. The Multi-Chassis kit provides you with everything you need to give your robot a unique tank tread platform with plenty of room for expansion to add various sensors and controllers.

Reference: RBD-1540

EL Wire-Blue 3m With Pocket Inverter

Input Voltage:12 V Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: Blue

Reference: RBD-1551

Pololu Ball Caster with 3/8″ Metal Ball

Metal Balls with ABS housings 3/8" diameter size Two spacers (1/16" and 1/8" thick) Easy to assemble

Reference: RBD-0284

5.8GHz Circular Polarized Mushroom Antenna RP-SMA Set Tx/Rx for FPV Multicopter

Gain: 2.0dBi-2.5dBi Antenna connector: RP-SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes

Reference: RBD-1399

2 Channel 12V Relay Board Module

Operating Voltage: 12V DC Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Equipped with high-current relay 10A@250VAC / 10A@30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick...

Reference: RBD-1207

Line Following Sensor 5 Array

High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...

Reference: RBD-0161

20x4 Character LCD

Model: LCD2004 Character Color: White Backlight: Blue Supply voltage: 5V Dimensions(L x W x H) mm: 98 x 60 x 12

Reference: RBD-1019

3S 20A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board 12.6V Cell

Charging Voltage: 12.6V-13V Overcharge Voltage Range: 4.25V-4.35V ± 0.05V Overpressure Voltage Range: 2.3V-3.0V ± 0.05V Upper Limit Operating Current: 5A-6A

Reference: 1709

37 GB 6mm Hex coupling for Robot Smart Car Wheel 30mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 6 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 50gm

Reference: RBD-0399

Graphic LCD 84x48 (Nokia 5110) Black on White for Arduino

Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue.

Reference: RBD-0233

Brand: SparkFun Electronics

SparkFun 9 Degrees of Freedom IMU Breakout - LSM9DS0

Description: This is the LSM9DS0, a versatile motion-sensing  system-in-a-chip that houses a 3-axis accelerometer, 3-axis  gyroscope, and 3-axis magnetometer. That’s right, 9 degrees  of freedom (9dof) from a single IC!

Reference: RBD-1069

N20 DC Gear Motor Wheel 3PI miniQ Car wheel Tyre

Wheel Outer Diameter: 44MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 18 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.

Reference: RBD-1537

EL Wire-White 3m With Pocket Inverter

Input Voltage:12 V Can offer 360 degrees of illumination Energy-saving, long lifetime Wire diameter:  2mm EL light length: 3M Lifetime: >12,000 hours Color: White

Reference: RBD-0343

12V 60W TEC1-12706 Thermoelectric Cooler Peltier

Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm

Reference: RBD-0563

3S 25A Balance 18650 Lithium Battery BMS

Overcharging and Over Discharging Protection Short circuit protection: Yes Applicable assembly: Nominal 4.5V Batteries / 3 strings.