DC 12V Solenoid Electric Door Lock

Reference: 828

Single Axis Servo Bracket

Robot Uniaxial Steering Gear Servo Bracket Metal Stent Bipedal Robot Manipulator DIY accessories -Black

Reference: 352

Knock Sensor Module KY-031 For Arduino ,PIC, AVR, Raspberry pi

Description knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher.Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.

Reference: 272

Brand: Waveshare

Logic Level Converter

Logic Level Converter

Reference: 315

US-015 Ultrasonic Module Distance Measuring Transducer Sensor

  Features: Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm

Reference: 31

Jumper Wire 40 Pcs Set

3 Types Available 1. Male to Male  2. Male to Female 3. Female-Female

Reference: 288

GY-801 - Multi Sensor Board

GY-801  Multi-Sensor Board - 3 Axis Gyro -3 Axis  Accelerometer - 3 Axis Magnetometer, Barometer, Thermometer

Reference: 415

801S Vibration Sensor Module vibration Analog Output Sensitivity LM393

01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...

Reference: 1112

DIY 6DOF Aluminum Robot Arm 6 Axis Rotating Mechanical Robot Arm Kit

Type 1: 6DOF Robot Arm Kit with 6 PCS Servos Type 2: Robot Arm Kit with Control board, Claw, 8 PCS Servos Name: 6DOF Robot Arm Kit Type: DIY robot Degree: 6 degrees of freedom Material: Stainless steel For: 8 years old and above Size: 270*105*215mm Note: Unassembled Delivery, which required you with patience and hands-on ability.           Assemble...

Reference: 654

Male Pin Header Single Row ( Short )

Male Pin Header Single Row  ( (Short) 40 pin set )

Reference: 314

Double-ended 50cm Cable Crocodile Clips

 Double-ended 50cm Cable  Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.

Reference: 1551

Pololu Ball Caster with 3/8″ Metal Ball

This small ball caster uses a 3/8″ diameter metal ball. The height of the assembled kit ranges from 0.4″ to 0.6″, depending on the combination of included spacers used.

Reference: 351

RFID M94 NFC thin smart card 13.56MHz 1k S50 IC

Specifications: This card is compatible with NFC capable phones and tablets, it is Smart Card Tags. Frequency: 13.56 MHz 1K byte EEPROM memory (768 FREE BYTES availability) Size: 85mm x 54mm x 0.9mm Material: PVC, Waterproof Write endurance 100,000 cycle Reading distance is 0 - 10cm (Reading distance depends on readers, not the cards)

Reference: 166

XBee 1mW Trace Antenna - Series 1 (802.15.4)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Reference: 563

3S 25A Balance 18650 Lithium Battery BMS

3S 11.1V 12.6V 25A W/Balance 18650 Li-ion Lithium Battery PCB Protection Board Specification: Brand newSize: about 56mm*45mm*1.2mmOver voltage range: 4.25-4.35v±0.05vOver discharge voltage range: 2.3-3.0v±0.05vMaximum operating current: 0-25AMaximum transient current: 34-40AQuiescent current: less than 30uA

Reference: 669

6 DOF Aluminium Mechanical Robotic Arm Clamp Claw Mount Robot Kit

6 DOF Aluminium Mechanical Robotic Arm Clamp Claw Mount Robot Kit

Reference: 150

5mW Adjustable Laser Dot Diode Module

5mW Adjustable Laser Dot Diode Module Features: 1. Output Power: 2-5mW2. Wavelength: 650nm3. Working Voltage: 3v - 5v4 .Laser Shape: Dot5. Working temperature: -10 C-40 C

Reference: 270

Brand: Waveshare

Raspberry Pi 3 Robot Shield Expansion Board Pioneer 600

What's on Board Raspberry Pi GPIO interface : for connecting Raspberry Pi USB TO UART : control the Pi through serial terminal AD/DA IO interface : screw terminal 1-WIRE interface : for connecting 1-WIRE devices like DS18B20 Sensor interface : for connecting various sensors 0.96inch OLED : SSD1306 driver, 128×64 resolution, SPI interface Buzzer

Reference: 313

RC522 RFID Card Reader Module Kit Android NFC supported

Specification: Module Name: MF522-ED Working current：13—26mA/ DC 3.3V Standby current：10-13mA/DC 3.3V sleeping current：<80uA peak current：<30mA Working frequency：13.56MHz Card reading distance ：0～60mm（mifare1 card） Protocol：SPI data communication speed：Maximum 10Mbit/s

Reference: 385

MCP23017 - i2c 16 input/output port expander

MCP23017 - i2c 16 input/output port expander

Reference: 176

Brand: SparkFun Electronics

Rover 5 Robot Platform 4 Motors 4 Encoders

  Rover 5 Robot Platform 4 Motors 4 Encoders Description: If you’re looking for a base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent motors, each with a hall-effect quadrature encoder and gearbox.

Reference: 1071

N20 Motor Mounting Bracket

Description This is a compact mounting bracket ideally designed for N20 micro gear motors. It is made of ABS plastic material and it is designed to fit perfectly to N20 motors. The motor bracket only suitable for N series motor, such as motor N20, N20 geared motors, N20 screw motor, N30 motor. Brief Data: Height: 11mm. Width: 25mm. Material: ABS plastic....

Reference: 1402

NodeMCU ESP8266 Expansion Base Board

NodeMCU ESP8266 Expansion Base Board This NodeMCU ESP8266 Expansion Base Board is an expansion board designed to work with the NodeMCU V3 ESP8266 ESP-12E. Powered by 6V to 24V DC input, it provides the support power to operate the NodeMCU V3, and provide easy connection to all of its input and output pins to help you connect your NodeMCU board to other...

Reference: 282

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Reference: 350

STM32F103C8T6 ARM STM32 Minimum System Development Board Module Arduino

Description:Model: STM32F103C8T6.Core: ARM 32 Cortex-M3 CPU.Debug mode: SWD.72MHz work frequency.64K flash memory, 20K SRAM.2.0-3.6V power, I/O.Reset(POR/PDR).4-16MHz crystal.On-board Mini USB interface, you can give the board power supply and USB communication.

Reference: 338

Brand: Waveshare

Dust Sensor For Arduino

Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm         in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear         with dust density Embedded voltage boost circuit to support wide range of power supply

Reference: 133

Breadboard (Large)

Solderless Large Breadboard 830-Point Solderless Breadboard 6.5" x 2.125" A breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard). Because the solderless breadboard for electronics does not require soldering, it is reusable. This...

Reference: 344

Weighing Sensor 24 Bit HX711 Dual-Channel

Weighing Sensor 24 Bit HX711 Dual-Channel Precision A/D Module Pressure Sensor. This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. 

Reference: 1367

RGB Full color LED SMD Module

The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266. RGB full color LED Module KY-009 for Arduino, emits a range of colors by mixing red, green and blue. The amount of each primary color is adjusted using PWM.

Reference: 142

Fingerprint Scanner - TTL (GT-511C3)

Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.

Reference: 386

Precision Real Time Clock Module DS3231 AT24C32 I2C

Precision Real Time Clock Module DS3231 AT24C32 I2C With Battery