• How to Place an Order

  • bKash Payment Method

  • Request for Quotation/ International Sourcing

Arduino Uno R3

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.

Price BDT 399
More
In Stock

EM4100 125kHz RFID Card

It is proximity ID card of 125KHz, EM4100. It has been specially manufactured and packaged to be clean from dust. And you can print any pictures on the PVC blank cards. You can use it with our RDM6300 RFID reader module.

Price BDT 15
More
In-Stock
All best sellers
CC3D Flight Controller OpenPilot STM32 32-bit Flexiport
  • CC3D Flight Controller OpenPilot STM32 32-bit Flexiport
  • CC3D Flight Controller OpenPilot STM32 32-bit Flexiport
  • CC3D Flight Controller OpenPilot STM32 32-bit Flexiport

CC3D Flight Controller OpenPilot STM32 32-bit Flexiport

Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac, and Linux.
Direct high-speed USB support with no drivers required, a true plug and play device.
BDT 1,800
rating Read the review
Average rating: 5/5 - Number of reviews: 1
Quantity
In-stock

  • Store Pickup Available! Store Pickup Available!
  • Shipping Available Shipping Available
Description
OpenPilot CC3D Flight Controller Bent Pin STM32 32-bit Flexiport

OpenPilot CC3D Flight Controller Bent Pin STM32 32-bit Flexiport for RC Drone FPV Racing Multi Rotor
OpenPilot CC3D Flight Controller Bent Pin STM32 32-bit Flexiport for RC Drone FPV Racing Multi Rotor
OpenPilot CC3D Flight Controller Bent Pin STM32 32-bit Flexiport for RC Drone FPV Racing Multi Rotor
OpenPilot CC3D Flight Controller Bent Pin STM32 32-bit Flexiport for RC Drone FPV Racing Multi Rotor

The CC3D provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes. 
 
CC3D CopterControl Hardware Features
Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
Software support for Windows, Mac and Linux.
Direct high speed USB support with no drivers required, a truly plug and play device.
Spektrum satellite receiver support.
Futaba S-BUS hardware support.
Innovative Flexi-port technology for superior port flexibility.
4Mbits on-board EEPROM for configuration storage.

Flexiport
CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
 
Superior user experience
OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
 
The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it!
 
Sensors and Components
3-axis Gyroscope array and 3-axis Accelerometer: MPU-6000
Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.
Simultaneous support for multiple receivers.
ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
10 PWM outputs to servos or ESC’s, or for camera stabilization
Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
Onboard USB connectivity for easy configuration.
USB and serial telemetry and configuration 
Supported by powerful OpenPilot GCS
4 Mbit onboard memory
3C Quaternion based complementary filter running at 500Hz

Note: 
Color: white and black (delivery randomly)


Installation settings for CC3D flight controller, click here.
 
Package included:
1 x CC3D Flight Controller
1 x 8p wire rod
2 x 4p expansion path
1 x flight controller case
Product Details
10 Items

Click here to leave a review

Works Fine
rating
30/05/2019
Asik
My quad is working fine. Best Controller in Cheap budget. And RoboticsBD helped me with installing driver.
30 other products in the same category:

Reference: WRL-10418

XBee Pro 63mW PCB Antenna - Series 2B (ZigBee Mesh)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Price BDT 4,600
More
Pre Order

L298N H-Bridge Dual Motor Driver, Stepper Motor Driver

This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver IC. This module will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor.

Price BDT 150
More
In Stock

Digispark Kickstarter ATTINY85 Arduino General Micro USB Development Board

Digispark USB Development Board The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when...

Price BDT 150
More
In-Stock

801S Vibration Sensor Module vibration Analog Output Sensitivity LM393

01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...

Price BDT 550
More
In-Stock

4 Channel Relay Board Module Optocoupler LED for Arduino PiC ARM

Relay modules suitable for switching of higher voltages and perfect for use with microcontrollers including Arduino, ARM, AVR and PIC. The relays used are rated up to 10A and have NO/NC contacts. Each channel has an LED indicator to show the relay is on.Channels: 4Connects directly to a microcontrollerSwitching Capacity: 10AMaximum Voltage: 250VAC /...

Price BDT 240
More
In Stock

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Price BDT 7,500
More
Last items in stock

Waterproof DS18B20 Digital Thermal Probe or Sensor

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!

Price BDT 250
More
In-Stock

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino 

Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...

Price BDT 1,200
More
Last items in stock

433MHz 100 Meters ASK Wireless Module Kit RF

STX882 Transmitter&SRX882 Receiver Antenna This 433MHz 100 Meters ASK Wireless Module Kit RF comes with a SRX882 Receiver Module, STX882 ASK Transmitter Module and SW433–TH32 spring antenna. The modules can be connected to the microcontroller directly. So it is more convenient for user developing wireless products.

Price BDT 350
More
In-Stock

AMG8833 IR Thermal Camera Breakout (Adafruit Compatible)

Add heat-vision to your project and with an AMG8833 Grid-EYE Breakout! This sensor from Panasonic is an 8x8 array of IR thermal sensors. When connected to your microcontroller (or raspberry Pi) it will return an array of 64 individual infrared temperature readings over I2C. It's like those fancy thermal cameras, but compact and simple enough for easy...

Price BDT 8,550
More
In-Stock

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Price BDT 1,200
More
In-Stock

N20 Motor Mounting Bracket

Description This is a compact mounting bracket ideally designed for N20 micro gear motors. It is made of ABS plastic material and it is designed to fit perfectly to N20 motors. The motor bracket only suitable for N series motor, such as motor N20, N20 geared motors, N20 screw motor, N30 motor. Brief Data: Height: 11mm. Width: 25mm. Material: ABS plastic....

Price BDT 50
More
In-Stock

Follow us on Facebook