How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: RBD-1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: RBD-245
Choose your desire Resistor value from below:
Reference: RBD-31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Arduino Bluetooth Module (HC-05)
This serial Bluetooth module can work as either master or slave. This module also includes the baseboard, not only the core board, most functions are pre-set, so only the serial port communication is available but it’s easier to use. It can be used also with Arduino or Microcontroller.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
Product Features:
Compatible with Arduino, Stamp, FPGA and many more!
Plug and Play operation at 9600 baud
Easily integrated into existing (9600 baud) projects without any need to modify code!
Includes: BT2S Slave, Easy-Pin Cable and Pin-out/Instruction Pamphlet
*Requires Bluetooth enabled master device.
Bluetooth module interface including VCC, GND, TXD, RXD, KEY pin
and LED Status pin-out (STATE).
In open space effective distance is 10 meter, more than 10 meter is
also possible by using external antenna.
Backplane set anti-reverse diode with 3.3V LDO input voltage of 3.6 ~~ 6V
unpaired current is about 30mA paired approximately 10mA input voltage
to prohibit more than 7V.
The module is not connecting with the phone!! It is not detecting it!! Help!!!
Reference: RBD-196
Brand: DFRobot
INTRODUCTION The APC220 radio module provides a simple and economic solution to wireless data communications. Integrates an embedded high speed microprocessor and high performance IC that creates a transparent UART/TTL interface, and elminates any
Reference: RBD-285
Brand: RoboticsBD
3D Printed Pan Tilt Camera Mount With Servo Motor Package Include: 1x 3D Printed Pan Tilt Bracket 2x 9g Servo Motor (Assambled with the Pan Tilt Bracket) Fully assembled 3D Printed (ABS Filament) strong Pan Tilt Camera Mount With Servo Motor 9g
Reference: RBD-227
Description: Solenoids are a great way to induce linear motion for pushing, pulling or controlling switches and levers.This smaller solenoid is designed to work directly with 5V~6V which makes it a great match for embedded projects. It has a throw of about 4.5mm and 2 M2 mounting holes on the body.
Reference: RBD-1682
12V 37GB550 Gear Motor High Torque 100 RPM Shaft: 37mm Voltage: 12V, DC RPM: 100 Torque: 10.0Nm Approximate
Reference: RBD-1336
ESP8266 ESP-01S 5V WiFi Relay Module Things Smart Home Remote Control Switch Phone APP ESP01 ESP-01 Wireless WIFI Module (ESP8266 is not included)
Reference: RBD-268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-231
Brand: SparkFun Electronics
Description: The Beaglebone Black is a low-cost credit -card-sized development platform with good support from a fast growing community. The Beaglebone Black differs slightly from the regular version by providing you with an onboard micro HDMI port, 512MB of DDR3L DRAM, 4GB onboard flash memory, an AM3358 processor at 1GHz, and making JTAG optional...
Reference: RBD-288
GY-801 Multi-Sensor Board - 3 Axis Gyro -3 Axis Accelerometer - 3 Axis Magnetometer, Barometer, Thermometer
Reference: RBD-31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-1560
It is a UPS uninterruptible power supply control board. DC 9V Support charging and discharging at the same time Large current Small size High efficiency Support short circuit protection
Reference: RBD-22
The HC-SR04 ultrasonic sensor uses sonar to determine the distance to an object like bats or dolphins do. It offers excellent range accuracy and stable readings in an easy-to-use package. It operation is not affected by sunlight or black material like Sharp rangefinders are (although acoustically soft materials like cloth can be difficult to detect)....
Reference: RBD-623
DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A
Reference: RBD-326
Brand: DFRobot
This 4WD Chassis is simple yet versatile robot chassis designed specifically for students and hobbyist. Featuring large size chassis plates cut from acrylic and designed with numerous holes and mounting points, providing plenty of space to carry a PCB board and any additional components that you choose. The possibilities are only limited by your...
Reference: 1708
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 50gm
Reference: RBD-1311
mDrawBot is a 4-in-1 drawing robot kit, it can be assembled into 4 different drawing robots: mScara, mCar, mSpider and mEggBot.
Reference: RBD-233
Brand: SparkFun Electronics
Description: This is the LSM9DS0, a versatile motion-sensing system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9dof) from a single IC!
Reference: RBD-34
MG996R 10kg Servo (Fully Metal) Brand Could be different variant
Reference: RBD-1069
QUICK OVERVIEW Wheel Outer diameter: 42MM Wheel width: 18 mm Tire material: Rubber Color: Black & White Weight: 43 gm Coder Accuracy: 12 pulses per revolution Wheel weight: 19.4 gm.
Reference: RBD-306
32 Channel USB UART Servo Motor Controller Application: Hexapod, Robotics Arm, Servo Drive This is the newly upgraded controller board. Up to 32 servo motors can be controlled at the same time, either by using a software on a PC, or UART communication ( TTL serial port) of MCU (51, AVR, ARM, FPGA, PIC, etc. to send commands to control the steering.
Reference: RBD-150
5mW Adjustable Laser Dot Diode Module Features: 1. Output Power: 2-5mW2. Wavelength: 650nm3. Working Voltage: 3v - 5v4 .Laser Shape: Dot5. Working temperature: -10 C-40 C
Reference: RBD-402
This keypad has 12 buttons, arranged in a 3×4 grid. It’s made of a thin, flexible membrane material The keys are connected into a matrix, so you only need 7 microcontroller pins (3-columns and 4-rows) to connect the key pad.
Reference: RBD-289
16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685 You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output.
Reference: RBD-1372
Features: - Powerful foot, high speed, corrosion-resistant Product information: - Voltage: 12-24V - Current: 20A - Power: 30-200W - Motor KV: 1000KV - Size: Wire length 250mm ,Diameter 74mm ,Total length 75mm ,Propeller diameter 60mm - Metrial: Motor 304 Stainless steel bearing+Aluminum alloy ,Shell PLA ,Propeller PC Package Include: 1x CW Underwater...
Reference: RBD-352
Description knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher.Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.
Reference: RBD-1402
NodeMCU ESP8266 Expansion Base Board This NodeMCU ESP8266 Expansion Base Board is an expansion board designed to work with the NodeMCU V3 ESP8266 ESP-12E. Powered by 6V to 24V DC input, it provides the support power to operate the NodeMCU V3, and provide easy connection to all of its input and output pins to help you connect your NodeMCU board to other...
Reference: RBD-180
Brand: SparkFun Electronics
Description: This is the same product as the Makey Makey Standard Kit. The difference is this version comes in fancy clamshell packaging meant for our distributors that need it. Regular customers are welcome to order, but we want to limit the amount of extra packaging finding its way into the trash heap.
Reference: RBD-1256
Brand: SparkFun Electronics
Rover 5 Robot Platform 2 Motors 2 Encoders Description: If you’re looking for a base for your next robot, look no further than the Rover 5. The Rover 5 uses 2 independent motors, each with a hall-effect quadrature encoder and gearbox.
Reference: RBD-1250
37GB-550 Gear Reducer Motor DC 12V 100 RPM Geared Motor High Torque 16.0 Kg.cm (Approximate Torque)
Reference: RBD-1182
Big Powerful Solder Sucker Desoldering Pump Repair Tools Suction Model GS-100 Solder Removal Tool
Reference: RBD-311
Features: Model: YF-S201 Sensor Type: Hall effect Working Voltage: 5 to 18V DC (min tested working voltage 4.5V) Max current draw: 15mA @ 5V Output Type: 5V TTL Working Flow Rate: 1 to 30 Liters/Minute Working Temperature range: -25 to +80℃ Working Humidity Range: 35%-80% RH Accuracy: ±10%
Reference: RBD-671
Gas Sensor(MQ2) module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke or Propane. Due to its high sensitivity and fast response time, measurement can be taken as soon as possible. The sensitivity of the sensor can be adjusted by the potentiometer.
Reference: RBD-494
Actiontec Original 12V Power AdapterModel#: STD-120200Output: 12V 2.0AInput: 100-240VAC,50/60 Hz,0.8ACompatible with: Arduino, CCTV, Wireless Router, DSL and Cable Modem, ONU, Media Converter, DVR, NVR
Reference: RBD-666
HX1838 NEC Code Infrared Remote Control Module DIY Kit
Arduino Bluetooth Module (HC-05)
This serial Bluetooth module can work as either master or slave. This module also includes the baseboard, not only the core board, most functions are pre-set, so only the serial port communication is available but it’s easier to use. It can be used also with Arduino or Microcontroller.
