Reference: RBD-2414

Yahboom 4 Channel Infrared Line Following Tracking Sensor Module

This tracking module adopts four tracking probes, and optimized spacing layout. The inner two probes can accurately identify the black line. The outer two probes can assist the inner probe to identify the black line and provide early warning. The car can recognize the 90°curved road and other difficult tracks. Knob-type adjustable resistors plus...

Reference: RBD-1949

DC12V N20 Gear Motor 70 RPM & Mount Bracket & 43mm Wheel

N20 Micro Gear 12V 70RPM DC Motor (High Torque) Mounting Bracket for N20 Micro Gear motors 3PI miniQ Car wheel Tyre 44mm N20 DC Gear Motor Wheel

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-1582

TDA7492P Bluetooth 4.2 CSR8635 Bluetooth Receiver Amplifier Audio Board 2x25W for 4/6/8/16 Ohm Speakers Module Parts Component

25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω Wide-range single-supply operation (8 – 26 V) High efficiency (η = 90%) Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB Differential inputs minimize common-mode noise Standby and mute features Short-circuit protection

Reference: RBD-0436

3D Printer Controller for RAMPS 1.4 REPRAP MENDEL PRUSA

Supply Voltage: 12V Standard interfaces (as that of the extruder) Reserved GCI like I2C and RS232 3 MOSFET’s are applied to the heater/ fan and thermistor circuit. Another 5A added to protect the component parts. An 11A fuse is added to the hotbed. Support 5 stepper drive board

Reference: RBD-0402

3×4 Flexible Keypad

Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC 

Reference: RBD-0716

65mm Rubber Wheel with 25GA Motor Mounting Bracket

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.

Reference: RBD-2259

3mm Motor Shaft Coupling Brass Hex 18mm length

Type: Hexagonal coupling. Material: brass. Inner diameter: 3 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 14.6gm

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0390

12V 37GB550 Gear Motor High Torque 60 RPM

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

Reference: RBD-1844

6.5 inch Jumper Wire (Pack of 2)

The head of the cables is stronger, Don’t worry it will easy to fall. Use for Arduino Or other kinds of circuit experiment. High quality and in good working condition Durable and reusable Easy to install and use

Reference: RBD-2263

8mm Hex coupling for Robot Smart Car Wheel 30mm Length

Type: Hexagonal coupling. Material: brass. Inner diameter: 8 mm. Total length: 30 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 18.6gm

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-1534

Planetary Gear Motor PG42-775 42 Gear Box Large

Model:PG42-775 Working volt range:12V. Rated volt:12V No-loading Rotation speed:110-120 Rpm Speed Ratio:91

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-0208

Off-Road Wheels - 130x60mm (Pair)

"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."

Reference: RBD-0311

YF-S201 Hall Effect Water Flow Meter / Sensor

Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD

Reference: RBD-0395

XL4015 DC-DC Step Down Adjustable Power Supply Module 5A Max

Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function. RoboticsBD

Reference: RBD-0234

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-2246

80mm Mecanum Wheel Omni-directional for Smart Robot with 4mm hubs Package

Color: Black Weight: 44g (each) Inner diameter: 3.3mm Outer wheel diameter: 60mm Thickness: 28mm 2 Left Wheel + 2 Right Wheel and 4 pcs of 4mm hubs   Compatible Motor: High Torque Gear Motor 12V 500RPM 25GA Compatible Motor: High Torque Gear Motor 12V 100RPM 25GA Compatible Motor: 12V 500RPM 25GA Gear Motor

Reference: RBD-1254

XiaoR STM32 Self Balancing Programmable Robot

Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct

Reference: RBD-0231

Brand: SparkFun Electronics

Beaglebone Black - Rev C

Sitara AM3358BZCZ100 ARM Cortex-A8 32-Bit RISC microprocessor, up to 1GHz Onboard HDMI to connect directly to TVs and monitors More and faster memory now with 512MB DDR3L 400MHz SDRAM, 4GB eMMC Memory Onboard storage frees up the microSD card slot for greater expansion Support for existing Cape plug-in boards TPS65217C PMIC regulator and one additional...

Reference: RBD-1573

Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip

Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm

Reference: RBD-2444

Optical Endstop Switch with 1m Cable

Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.

Reference: RBD-1301

Multi-Chassis - Rescue Platform Complete Kit

Tracked tank climber robot kit with two 48:1 DC motors Designed with robotic top-level climbing structure Can run in high grass or sandy ground Able to climb over steps up to 150mm high

Reference: RBD-0196

Brand: DFRobot

APC220 Radio Communication Module

INTRODUCTION The APC220 radio module provides a  simple and economic solution to wireless data communications. Integrates an  embedded high speed microprocessor  and high performance IC that creates a  transparent UART/TTL interface, and  elminates any

Reference: RBD-0653

Male Pin Header Single Row (L Shaped)

Can be manually broken for the length needed. Connector: Pin Header 2.54mm Pitch Connector type: Pin Strips Male Number of pins: 40 Right angled male berg strip. (L Shaped)