

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Double-ended 50cm Cable Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.
Click here to leave a review
Specifications:- Gain: 2.0dBi-2.5dBi- Standing-wave ratio (SWR): <1.5- Directivity: Omni-directional- Center frequency: 5.8Ghz- Connector: RP-SMA- Diameter of connector: 7.67mm- Length:Transmitter antenna:71mm- Receiver antenna:91mm- Net weight: 12g(Tx/Rx)- Package weight:69 g
Overview RDM6300 125KHz cardreader mini-module is designed for reading code from 125KHz card compatible read-only tags and read/write card . It can be applied in office/home security, personal identification, access control, anti-forgery, interactive toy and production control systems etc.
Module Voltage: DC6-15V;Operating Current: less than 5mA;Transmitting Power: less than 2mAOutput Signal: TTL trigger repeated, high and low. High output 5V, low level 0V;Detection Angle: 180 degrees (hemispherical);Detection Range: 3-8m,the default setting is 7mWork Delay: 2S-120S,the default setting is 20S
Powerful High Torque DC Gear Motor with Encoder Voltage: 12V DC RPM:100RPM Diameter: 37mm Shaft length: 15mm Length (excl. shaft): View Photos Shaft diameter: 6mm White and red cord : (+)(-) power cord Yellow and blue cord: For Encoder
1. WULI bot is an educational robot for beginners to learn the knowledge of STEAM, and it has a variety of functions. Such as following functions, ultrasonic distance measurement, maze adventure, gesture control and so on. This robot is inspired from Wall-e Movie by Pixar
Specification:1. "LIGHT" linked with GND, the backlight to be lit.2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3. Use a 3.3V controller, otherwise the display could be quite vague.
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!
DC-DC 9V/12V/24V to 5V USB Step Down Power Module 2A
Relay modules suitable for switching of higher voltages and perfect for use with microcontrollers including Arduino, ARM, AVR and PIC. The relays used are rated up to 10A and have NO/NC contacts. Each channel has an LED indicator to show the relay is on.Channels: 2Connects directly to a microcontrollerSwitching Capacity: 10AMaximum Voltage: 250VAC /...
This is a 5V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) .
Description: Type K Type. Mounting thread: M6 Temperature Range:0-600°C. Thread Diameter:6mm / 0.23". Internal Insulation:Fibreglass. External Shielding:Metal Shield. Total Length:1M / 39". Fork Terminal Spacing: 3.5mm / 0.13". Color: As Picture Shown. 10mm thread sensor for accurate measurement.
This is a 3DPrinted robotic arm.The design intent was to make something "easy" to make robotics armIt uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it.All the pieces are 3DPrinted in PLA. This is a fully built and assembled mini Robotics Arm with servos (4 dof) Included:...
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 100 Torque: 35KG.CM
Voltage: 5VDiameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 64Stepper Motor Driver Board with ULN2003A, B, C, D four-phase LED indicates the status of the stepper motor workStepper motor with a standard interface, when used directly pluggable
The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Brand: SparkFun Electronics
Features: Range: 0-40m Laser Emitter Accuracy: +/- 2.5cm at distances greater than 1m Power: 4.75–5V DC; 6V Max Current Consumption: 105ma idle; 130ma continuous Rep Rate: 1–500Hz Laser Wave Length/Peak Power: 905nm/1.3 watts Beam Divergence: 4 m Radian x 2 m Radian Optical Aperture: 12.5mm Interface: I2C or PWM
15mmx24mm Speaker, rated power is 1W, impedance is 8 Ohm This small speaker will be your best choice in DIY audio speakers it will work well for home audio-visual equipment and other speakers Unique design, adopted well-performed magnet, imported rubber coil The package includes 1pcs small speakers, if the item you have received is defective or get some...
This plastic wheel with rubber tyre features a slot which allows it to be attached to our MO1014 geared DC motor.