TCRT5000L Reflective Optical Sensor

YF-S201 Hall Effect Water Flow Meter / Sensor

Features: Model: YF-S201 Sensor Type: Hall effect Working Voltage: 5 to 18V DC (min tested working voltage 4.5V) Max current draw: 15mA @ 5V Output Type: 5V TTL Working Flow Rate: 1 to 30 Liters/Minute Working Temperature range: -25 to +80℃ Working Humidity Range: 35%-80% RH Accuracy: ±10%

Current Sensor ACS712-30A

Product Description 1. Current sensor chip: ACS712ELC-30A. 2. Pin 5V power supply, on-board power light. 3. The module can be measured plus or minus 30A current, Corresponding analog output of 66 mV / A. 4. No test current through, the output voltage is VCC / 2. 5. PCB size: 31 (mm) x13 (mm). 

Sound Sensor Module for Arduino

DS1302 Real Time Clock Module (DS1302Z clock chip,32.768KHZ crystal)

MQ-5 Smoke Gas Detector Sensor

The MQ series of gas sensors use a small heater inside with an electrochemical sensor. They are sensitive to a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino.

Brand: SparkFun Electronics

SparkFun ToF Range Finder Sensor - VL6180

Description: This is the SparkFun “Time-of-Flight”  Range Finder, a sensor board for the VL6180  distance sensor. Unlike most distance sensors  that rely on reflected light intensity or reflected  angles to determine range, the VL6180 uses a  precise clock to measure the time it takes light  to bounce back from a surface.

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Brand: SparkFun Electronics

SparkFun 9 Degrees of Freedom IMU Breakout - LSM9DS0

Description: This is the LSM9DS0, a versatile motion-sensing  system-in-a-chip that houses a 3-axis accelerometer, 3-axis  gyroscope, and 3-axis magnetometer. That’s right, 9 degrees  of freedom (9dof) from a single IC!

Flame Sensor fire detection module for Arduino

GY-9960LLC APDS-9960 RGB and Gesture Sensor Module

Specification:1. Small size: 11mm*27mm2. Low power consumption: Supply voltage 2.5V ~ 5V, operating current is microamps3. Linear Good4. High Sensitivity5. High stability6. Detection range: 240nm-370nm7. Large angle: 130 degrees8. The Schottky type of photodiode for photoelectric mode

801S Vibration Sensor Module vibration Analog Output Sensitivity LM393

01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...

FPM10A Optical Fingerprint Reader Sensor Modules (With Shield)

FPM10A Optical Fingerprint Reader Sensor Modules Connect RoboticsBD Fingerprint Shield on top the Arduino Uno R3 Install Adafruit Fingerprint Library (Check Download Tab) Upload this code to Arduino Uno Board (Arduino Code SFG Demo) Run SFG Demo V2.0 Windows Test Software as Administrator

Proximity Sensor Switch E2E-X5ME1

5mm NPN Proximity Sensor Switch E2E-X5ME1 

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

6DOF MPU 6050 3 Axis Gyro

FM Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz

FM Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz

Line Follower Sensor- 8 Array

Compatible with Pololu QTR-8RC Library  Max Distance from Ground: 3mm. Digital Line Follower Parameters: 1. Working voltage:5V2. 8-channel infrared detector / IR Reflectance  Applications: 1. Robot2. Smart Car3. Laboratory4. DIY

Si7021 Industrial High Precision Humidity Sensor I2C Interface for Arduino

Features: Precision Relative Humidity Sensor± 3% RH (max), 0–80% RHHigh Accuracy Temperature Sensor±0.4 °C (max), –10 to 85 °C0 to 100% RH operating rangeUp to –40 to +125 °C operating rangeWide operating voltage (1.9 to 3.6 V)

MQ-135 Gas Sensor

MQ-135 module is widely used in air quality control equipments for buildings/offices, are suitable for detecting of NH3,NOx, alcohol, Benzene, smoke,CO2 ,etc

Brand: Waveshare

Dust Sensor For Arduino

Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm         in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear         with dust density Embedded voltage boost circuit to support wide range of power supply

VL6180 VL6180X ToF Range Finder Sensor

2.8V Regulator - Provides the required 2.8V for the sensor I2C Level Shifter - Provides logic level conversion from 2.8V to VCC 3-in-1 Module IR Emitter Range Sensor Ambient Light Sensor Measures absolute range up to 10cm Gesture Recognition I2C Interface Two Programmable GPIO Sharp Sensor Board Layout

MAX31865 SPI PT100/PT1000 RTD-to-Digital Converter Board

Knock Sensor Module KY-031 For Arduino ,PIC, AVR, Raspberry pi

Description knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher.Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.

Angle Sensor Module for Arduino SW-520D

Angle Sensor Module for Arduino High-sensitivity angle sensor SW-520D Comparator output, clean signal, great waveform, strong driving ability, more than 15mA Distribution positioner sensitivity adjustment Working voltage: 3.3V~12V Output form: Digital switching output (0 and 1) With fixed bolt hole for easy installation

Brand: Waveshare

Logic Level Converter

Arduino GSM / GPRS / GPS Shield

Overview GSM/GPRS/GPS Shield is an Arduino shield based on the Quad-band GSM/GPRS/GPS module SIM908.

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino

Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...

APDS-9930 RGB and Gesture Sensor

Description: This is RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price.

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000

Model: SCT013 Frequency: 50HZ-150KHZ Retractable transformer SCT-013 Rated Input Current : 100A Model : SCT-013 Rated Input Current : 60A / 100A

GY-801 - Multi Sensor Board

GY-801  Multi-Sensor Board - 3 Axis Gyro -3 Axis  Accelerometer - 3 Axis Magnetometer, Barometer, Thermometer