Reference: RBD-0674

MQ-5 Smoke Gas Detector Sensor

Model: MQ-5 Operating Voltage: 5V DC Operating Temparature:-20~40 degree celcius

Reference: RBD-0812

High Accuracy I2C MAX30105 Particle Optical Sensor Photodetectors Oximeter Module

Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.

Reference: RBD-0424

Si7021 Industrial High Precision Humidity Sensor I2C Interface for Arduino

SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface

Reference: RBD-1193

3mm Infrared Emitter and Detector

Infrared Photodiode Transmitter 3mm Infrared Photodiode Receiver 3mm

Reference: RBD-0150

5mW Adjustable Laser Dot Diode Module

Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~＋40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser

Reference: RBD-1197

TSOP38236 IR Infrared Receiver

The TSOP38236 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor.

Reference: RBD-1207

Line Following Sensor 5 Array

High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...

Reference: RBD-0575

PH Meter Digital Tester Aquarium Pool Water Urine Wine LCD Pen Monitor Protable

Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration

Reference: RBD-1833

Soil NPK Sensor Agricultural

NEW TYPE AVAILABLE CLICK HERE Measurement range: 0-199 mg/KG Measurement accuracy: +-2%F.s Resolution: 1mg/KG (mg/L) Response time (T90, s): less than 10 Communication port: RS485 Power supply: 5V-24v DC 

Reference: RBD-0357

GY-ML8511 Ultraviolet Light UV Sensor Module

Operating voltage (VCC): 3 V to 5V Operating current: 120μA (typical) 190μA (max) Operating Temperature: -40°C ~ +85°C Photodiode sensitive to UV-A and UV-B Embedded operational amplifier Analog voltage output Low supply current (300uA type) and low standby current (0.1uA type) RoboticsBD

Reference: RBD-2100

Flame Sensor Module

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-0233

Brand: SparkFun Electronics

SparkFun 9 Degrees of Freedom IMU Breakout - LSM9DS0

Description: This is the LSM9DS0, a versatile motion-sensing  system-in-a-chip that houses a 3-axis accelerometer, 3-axis  gyroscope, and 3-axis magnetometer. That’s right, 9 degrees  of freedom (9dof) from a single IC!

Reference: RBD-0417

Force Sensitive Resistor - Square

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-2152

Human Presence Radar LD2410 Respiration and Heartbeat Monitoring Non-contact Induction Sensor

Human Presence Radar LD2410 Respiration and Heartbeat Monitoring Non-contact Induction Sensor High-sensitivity 24GHz sensing module

Reference: RBD-0023

HC-SR501 PIR Motion Sensor

Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default)  Work temperature: -20-+80°C

Reference: RBD-0414

Waterproof DS18B20 Digital Thermal Probe or Sensor

A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...

Reference: RBD-1190

NTC Thermistor 10K

Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance  10kΩ Tolerance: ±1% Maximum Power Rating: 75mW Maximum Operating Temperature: +150°C Minimum Operating Temperature: -80°C Dimensions(dia.): 2 mm Length: 30mm Application: Compensation, Control, Measurement, etc.

Reference: RBD-0348

Heart Rate Pulse Sensor Module For Arduino

A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....

Reference: RBD-1756

TMP36 Temperature Sensor

TMP36 Temperature Sensor Low Voltage Temperature Sensors

Reference: RBD-0320

MAX6675 Module + K Type Thermocouple Sensor (Arduino compatiable)

Internal integrated cold junction compensation circuit. RoboticsBD With a simple three serial SPI interface; Temperature signal can be converted into 12-bit digital Embedded thermocouple break detection circuitry. High impedance differential inputs. Operating Voltage(VDC): 3 to 5.5 Temperature Range(°C): 0 to +1024 Cold Junction Compensation Range(°C):...

Reference: RBD-1348

Automatic Infrared PIR Motion Sensor Switch 12V

Easy to install. Automatic, convenient, safe and practical. It has the function of power and detection indication. The motion sensor can identify day and night automatically.

Reference: RBD-2444

Optical Endstop Switch with 1m Cable

Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.

Reference: RBD-1374

DHT21 AM2301 Temperature & Humidity Sensor

Model: AM2301. Supply voltage: 3.3 ~ 5.2 V DC. Signal output form: Digital signal output. Temperature measurement range: -40 ~ +80 ºC. Temperature measurement precision: ± 0.5ºC Humidity range: 10%~90%RH. Humidity measurement precision: ±3%RH.

Reference: RBD-0288

GY-801 - Multi Sensor Board

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0676

MQ-7 Carbon Monoxide Gas Sensor

Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm. RoboticsBD

Reference: RBD-0428

APDS-9930 RGB and Gesture Sensor

Operational Voltage: 3.3V. Ambient Light & RGB Color Sensing. Proximity Sensing. Gesture Detection. Operating Range: 4-8in (10-20cm). I2C Interface (I2C Address: 0x39). RoboticsBD

Reference: RBD-2206

Analog Piezoelectric Ceramic Vibration Module

Analog piezoelectric ceramic vibration module Measures the extent of vibration Proportional to the strength of shock or vibration Interface type: Analog Output Dimensions: 30 (L) x 23 (W) x 17 (H) Weight: 5g

Reference: RBD-1757

ADXL346 3-Axis Digital Gravity Acceleration Sensor Module

Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity: X: 28.6 LSB/g. Y: 31.2 LSB/g. Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection.

Reference: RBD-2081

Mini Dry Reed Pipe Module

Operating Voltage: 3.3V to 5v Output Type: Digital