
Reference: RBD-1354
Jumper Wire Single Medium
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: RBD-0094
Arduino UNO in Bangladesh Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6.
PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃
PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃
The latest price of PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃ in Bangladesh is BDT 500 You can buy the PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃ at best price from our RoboticsBD or visit RoboticsBD.
Please note that the product information provided on our website may not be entirely accurate as it is collected from various sources on the web. While we strive to provide the most up-to-date information possible, we cannot guarantee its accuracy. We recommend that you always read the product labels, warnings, and directions before using any product |
Product Images are shown for illustrative purposes only and may differ from the actual product. |
Reference: RBD-1644
940nm laser classified as class 1 under operation condition by IEC 60825-1:2014-3rd edition Small ceramic package(20×13.2×2.0mm) Long range absolute range measurement up to 1.8m within 5% accuracy at indoor
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-1195
Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance 10kΩ Tolerance: ±1%
Reference: RBD-1422
Processor: NXP LPC4330, 204 MHz, dual core Image sensor: Aptina MT9M114, 1296×976 resolution with integrated image flow processor Lens field-of-view: 80 degrees horizontal, 40 degrees vertical Power consumption: 140 mA typical Power input: USB input (5V) or unregulated input (6V to 10V) RAM: 264K bytes Flash: 2M bytes
Reference: RBD-0693
Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-1192
Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.
Reference: RBD-1858
CDD-11P PNP Output Photoelectric sensor Epoxy filled housing ensures resistance to vibration Rigid Nickel Plated Brass housing This is PNP Output CDD-11P. For NPN Output CDD-11N please check here.
Reference: RBD-2210
Specification:Item Type: Photoelectric Switch SensorBrand: BERMModel: E3F-DS30C4Power Supply Voltage: DC10-30VWorking Current: 200mAInduction Distance: 5-30cm (unit: cm)Response Time: 1msPower Cord Length: 1.2 metersOutput Form: DC three-wire normally open NPN NODetection Object: Transparent / opaque objectWorking Environment Temperature: -25- +75Cable...
Reference: RBD-2146
Operating voltage:3.3V/5V Sensitivity: Adjustable via a potentiometer Input Signal: Resistance, NOT Conductivity Output Signal: Voltage, analog reading Finger contact material: Nickel
Reference: RBD-0559
Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA 0-5V to 4-20mA Linear Conversion
Reference: RBD-1854
This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.
Reference: RBD-1719
Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in Germany
Reference: RBD-2078
No direction, any angle can trigger the work. Sensitivity switches can be selected for the trigger sensitivity according to circuit requirements. This switch is suitable for the trigger of the small current circuit. Component Type: SW-18015P Maximum voltage: 12V Rated Heating Current: 20mA
Reference: RBD-0313
This is RFID Reader/Writer RC522 SPI S50 CARD AND KEYCHAIN which works on non-contact 13.56mhz communication, is designed by NXP as low power consumption, low cost, and compact size read and write chip, is the best choice in the development of smart meters and portable hand-held devices. It uses an advanced modulation system, fully integrated at...
Reference: RBD-1951
High hardness, Corrosion protection. Waterproofness and High precision. The mode of its output signal:0-5V(Voltage signal). supply voltage: DC 12-24V. Power consumption:Voltage MAX≤0.3W. Start wind speed:0.4-0.8m/s.
Reference: RBD-1976
High sensitivity for Low-Light Operation. Low Operating Voltage for Embedded Portable Apps. Supports Scaling. The Standard SCCB Interface is Compatible with the I2C Interface.
Reference: RBD-1198
Industrial Systems Consumer Products Thermometers Thermally Sensitive Systems
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-1197
The TSOP38236 is a miniaturized receiver for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor.
Reference: RBD-1914
Working voltage 3.3V-5 Output format: digital switching output (0 and 1)A fixed bolt holes for easy installation
Reference: RBD-2130
9DOF IMU Breakout9 can capture nine different types of motion or orientation of the 3-axis accelerometer to obtain the relevant data magnetic orientation and angular velocity that is three-axis gyroscope + triaxial accelerometer three-axis magnetic field +
Reference: RBD-2224
Voltage – 250V Easy PCB mounting Good consistency Widely acclaimed
Reference: RBD-1203
Distance measuring range: 10 cm to 80 cm Output type: Analog voltage Output voltage differential over distance range: 2.05 V (typical) Update period: 38 ± 10 ms
Reference: RBD-1934
Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics
Reference: RBD-1848
Compact Design Country Specific pressure Multiple Displayable Unit Multi-colored, two-part display Alphanumeric display
Reference: RBD-1191
Internal filter for PCM frequency. Inner shield, good anti-interference ability. High immunity against ambient light. Improved shielding against electric field disturbance 3.0V or 5.0V supply voltage; low power consumption. TTL and CMOS compatibility. Suitable transmission code:NEC code,RC5 code. Universal receiver. 38 KHz. Infrared remote control receiver.
Reference: RBD-0553
Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0661
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1717
Wide voltage operation: 3.3~5.5V 0~2.3V analog signal output, compatible with 5V, 3.3V two control systems The excitation source is an AC signal, effectively preventing probe polarization Waterproof probe for long-term immersion in water
Reference: RBD-1264
Car body Material: Aluminum Alloy Car Wheel: Plastic Car strap: Plastic Color: Blue Input Voltage: 12V Weight: 1.2KG Motor & Tanks Chassis is included. No Electronics Parts
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-0992
Resistance: 10k Ohm Tolerance: 10 % Temperature coefficient: ±100 ppm/ºC Operating temperature range: -55ºC to +125ºC Mounting type: Through-hole
Reference: RBD-1164
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃