Proximity Sensor Switch E2E-X5ME1

Arduino GSM / GPRS SIM900 Shield

Details: The GPRS Shield is based on SIM900  module from SIMCOM and compatible with  Arduino and its clones. The GPRS Shield  provides you a way to communicate using  the GSM cell phone network.

Geiger Counter Kit Nuclear Radiation Detector Gamma Ray Build Radiation Monitoring Station

Specifications: Name:Radiation Detector system Model:508295 Geiger tube parameters: Technical parameters diameter:Φ10±0.5mm

Waterproof DS18B20 Digital Thermal Probe or Sensor

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!

Optical Dust Sensor - GP2Y1010AU0F

Supply voltage: 5-7V Operating temperature: -10-65 Celsius degree Consumption current:20mA max GP2Y1010AU0F is a dust sensor by optical sensing system

Angle Sensor Module for Arduino SW-520D

Angle Sensor Module for Arduino High-sensitivity angle sensor SW-520D Comparator output, clean signal, great waveform, strong driving ability, more than 15mA Distribution positioner sensitivity adjustment Working voltage: 3.3V~12V Output form: Digital switching output (0 and 1) With fixed bolt hole for easy installation

Honeywell HMC5983 Temperature Compensated Three-Axis Digital Compass

The HMC5983 includes our state-of-the-art, high-resolution HMC118X series magnetoresistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I²C or SPI serial bus allows for easy interface.

Fingerprint Scanner - TTL (GT-511C3)

Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.

Arduino GSM / GPRS / GPS Shield

Overview GSM/GPRS/GPS Shield is an Arduino shield based on the Quad-band GSM/GPRS/GPS module SIM908.

I2C Level Conversion Module 3~5V Fro Arduino

Specification   Level conversion for Arduino Board with 5V-3V regulated power supply module; 2-channel 5-3V dual-directional communication interface, IIC / I2C level conversion module, 3~5V system

High Sensitive Microphone Sound Sensor Detection Module

High Sensitive Microphone Sound Sensor Detection Module Feature:1. AO, analog output, real-time output voltage signal of the microphone2. DO, when the sound intensity reaches a certain threshold, the output high and low signal  

Double-ended 50cm Cable Crocodile Clips

 Double-ended 50cm Cable  Crocodile Clips 5 colour available Red, Black, White, Green, Yellow.

FM Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz

FM Transmitter Module Wireless Microphone Surveillance Frequency 88-108MHz

Water Level Sensor Depth of Detection Water Sensor for Arduino

Brand: Waveshare

Liquid Level Sensor for Arduino (WaveShare)

Specifications Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm

Analog pH Sensor / Meter Kit For Arduino

Need to measure water quality and other parameters but haven't got any low cost pH meter? Find it difficult to use with Arduino? Analog pH meter, specially designed for Arduino controllers and has convenient and practical "Gravity" connector and a bunch of features

IR Infrared Obstacle Avoidance Sensor Module

HSM-20G analog temperature & humidity sensor

BH1750FVI Digital Light intensity Sensor

Chip: BH1750FVI Power Supply: 3.3V - 5V Light Range：0 - 65535 lx(Lux) Sensor Built-in: 16 bit AD converter Size(L x W): Approx. 3.2cm x 1.5cm Direct digital output, bypassing the complex calculation, bypassing the calibration Close to the spectral characteristics of visual Widely used to 1-lux high precision measurement Standard NXP IIC communication...

Voltage to Current Transmitter Signal Module 0-5V to 4-20mA Linear Conversion

Voltage to Current Transmitter Signal Module 0-5V to 4-20mA Linear Conversion

MQ-5 Smoke Gas Detector Sensor

The MQ series of gas sensors use a small heater inside with an electrochemical sensor. They are sensitive to a range of gasses and are used indoors at room temperature. The output is an analog signal and can be read with an analog input of the Arduino.

MAX6675 Module + K Type Thermocouple Sensor (Arduino compatiable)

Smart Speed Detecting Sensor for Arduino

Reference: Venus GPS Sparkfun

Brand: SparkFun Electronics

Venus GPS with SMA Connector

Features: Up to 20Hz update rate -148dBm cold start sensitivity -165dBm tracking sensitivity 29 second cold start TTFF 3.5 second TTFF with AGPS 1 second hot start 2.5m accuracy Multipath detection and suppression Jamming detection and mitigation SBAS (WAAS / EGNOS) support 67mW full power navigation Works directly with active or passive antenna

HX1838 NEC Code Infrared Remote Control Module DIY Kit

HX1838 NEC Code Infrared Remote Control Module DIY Kit

TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino

The TTP229 is capacitive sensing design specifically for touch pad controls. The device has a built in regulator for the touch sensor. Stable sensing method can cover diversity conditions. Interface control panel links through non-conductive dielectric material. The main application is focused at replacing of the mechanical switch or button.

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino 

Type: Microwave SensorChip: HB100Frequency: 10.525GHzVoltage: DC 5V±0.25VCurrent: 40mASize: 38 x 45 x 7 mm (L x W x H)Application: Automatic door startup, Car, House intrusion alarm, Collision warningTraffic monitoringNote:Please pay attention to the Voltage/Current/Power of your own devices.To ensure product safety, check whether this item is compliant...

HC-020K Double Speed Measuring Module With Speed Encoder Kit

Description:Working voltage: 4.5V to 5.5 V.Transmit tube pressure drop: Vf = 1.6 VTransmit tube current: 20 mASignal output: A, B two way; The TTL levelDistinguish precision: 0.01 mmMeasurement frequency, 100 KHZEncoder diameter: 24 mmEncoder type D hole diameter: 4 mmThe encoder resolution: 20 line

Air Quality Breakout - CCS811

CCS811 Carbon Monoxide CO VOCs Air Quality Digital Gas Sensor Total Volatile Organic Compound (TVOC) sensing from 0 to 1,187 parts per billion eCO2 sensing from 400 to 8,192 parts per million Five Operating Modes Integrated MCU Onboard Processing Standard I2C Digital Interface Optimized Low-Power Modes Optional NTC Thermistor Pins

MQ-7 Carbon Monoxide Gas Sensor

MQ-7 Carbon Monoxide Gas Sensor This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance.

Reference: SparkFun

Flex Sensor 2.2"

Description: A simple flex sensor 2.2" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - they claim these sensors were used in the originalNintendo Power Glove. I love the Nintendo Power Glove. It’s so bad!