How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2762
The GY-362 ADXL362 Sensor Module is a high-precision accelerometer module designed for a wide range of motion sensing applications. Powered by Analog Devices' ADXL362, this module offers ultra-low power consumption, exceptional accuracy, and versatile functionality.
Reference: RBD-2558
This is a mini Laser light module with onboard triode current amplifier circuit, it gets only 1.3mA from the SIG pin so it is compatible with much more MCU. Note: For safe use, the module must not directly illuminate human eyes or irradiate human body for a long time. Features: - Output wavelength: 650nm - Working voltage: 4.75-5.5V - Working current:...
Reference: RBD-2783
The GY-51 LSM303DLH chip has an accelerometer, magnetometer, A / D converters and signal conditioning circuit integrated. Still, the communication to the processor is done through the I2C bus. Thus only one chip is required to achieve a six-axis data detection and output. The LSM303DLH requires very little peripheral devices.
Reference: RBD-2661
The sensor reacts to an interruption in the beam of infrared light that is transmitted between the transmitter and receiver. When the beam is interrupted by another object, the receiver signals this event by lighting up. The module is equipped with a 3 mm IR LED with an illumination angle of 10°. Beam interruption systems are used e.g. in measuring gates.
Reference: RBD-2790
The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current...
Reference: RBD-2715
Visible light to analog voltage converter for measuring the intensity of visible light. Visible light sensitivity with peak at 570nm +/- 60 degree angle of sensitivity Fast reacting in uSec range. Analog voltage output proportional to the intensity of light falling on the detector 3.3 and 5V compatible
Reference: RBD-2792
This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is upright. Tilt the case over and the balls don't touch, thus not making a connection. There are numerous uses for these basic sensors, but keep in mind you might need to use some debouncing code, as the sensor...
Reference: RBD-2763
Uses infrared to detect a reflective line on the floor.
Reference: RBD-2836
Operating Voltage: 3.5V-5V Supply Current: 15mA Optimal Sensing Distance: 3mm Designed with the reflected infrared sensor, indicator light. Built in a potentiometer for sensitivity control. On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L Signal detection sensitivity can adjust Reserve all the way more circuits (P3 voltage drawn)
Reference: RBD-2842
The QRE1113 breakout board offers a digital output solution, utilizing a capacitor discharge circuit to assess reflection levels. This compact board is designed for line sensing applications, particularly suitable when only digital I/O pins are available in the system. It is compatible with both 3.3V and 5V systems, providing versatility in various...
Reference: RBD-2888
A sensor that allows you to measure your pulse with your finger using a phototransistor. The red LED lights up each time it detects a pulse. Powered by 5 V.
