Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2409
10K adjustable precision potentiometer. 3 x Independent push buttons. Piezo buzzer. DS18B20 temperature sensor interface. LM35 temperature sensor interface. Infrared receiver interface.
Reference: RBD-2426
1.5V USB ultrasonic mist maker driver board and atomizer plate. 2. Low driving voltage, low power, low impedance, stable waveform, high conversion efficiency. 3. Round ring atomizer plate, middle spray, 5um ultra-fine spray aperture, 740 ultra-dense spray holes. 4. The surface of the atomizing sheet adopts an oxidation-resistant silver layer to protect...
Reference: RBD-2415
Dual PS2 Game Joystick Button Module Joystick Compatible With Arduino is a module use to connect and interface PlayStation 2 (PS2) game joysticks with an Arduino microcontroller board. It provides a simple and convenient way to control various projects and applications using PS2-style joysticks. The module consists of two PS2 joysticks, each with two-axis...
Reference: RBD-2444
Designed for use as an endstop for 3D printers but it can be used for other IR beam interrupter purposes as well.
Reference: RBD-2449
Boosts a 3.5 – 35V input up to a 5 – 56V output @ up to 2A Require a Heatsink
Reference: RBD-2458
The XH-M404 Adjustable DC-DC Step-Down Module can can step-down the input voltage to a range of 1.25 – 36V at up to 8A.
Reference: RBD-2466
This XL4015-based voltage converter is a 180 KHz fixed frequency PWM buck (step-down) DC/DC module with Constant Voltage and Constant Current control, capable of driving a 5A load with high efficiency, low ripple and excellent line and load regulation.
Reference: RBD-2555
This is a self-contained switching module that energizes / de-energizes a relay based on the humidity level. Just add 5V power and hook up the load you want to control then adjust the potentiometer to set the relative humidity level at which you want the relay to switch between ON / OFF. This type of module can be used for applications such as to...
Reference: RBD-2728
Temperature controller module for both heating and cooling applications.
Reference: RBD-2760
RS422 interface, two-way communication. B Y Z A ultra far transmission 1000 meters The module has ESD 15KV protection. Onboard to increase the limit of 10 ohms current limiting current protection. Module with TVS diode. Anti lightning, peak voltage. The module has 120-ohm termination resistors, which can effectively reduce the interference of long-range...
Reference: RBD-2892
Model: SNA118 Material: Plastic Plastic Type: PC Tool Supplies: CuttingDoes not Include ESP Wireless Module
Reference: RBD-2919
This mono Class D amplifier module with a surprisingly compact form factor - less than 2cm on a side - uses a MAX98357 chip to deliver 3W of power. Its I2S input allows an easy association with a Raspberry Pi or ESP32, allowing for example to design a small portable amplified speaker.