Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-0491
Sensor Type: Inductive Sensing Distance: 0.197" (5mm) Output Type: NPN-NO, 3-Wire Response Frequency: 400Hz
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-0492
Proximity-sensing / Diffuse Type Voltage: DC 6-36V Current: 300mA Sensory Distance: 5mm
Reference: RBD-1606
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
Reference: RBD-0686
Supply voltage 5-30VDC Detection distance 10mm (effective detection distance 0-10mm) Load current 150MA (no more than) Output form NPN three lines
Reference: RBD-1678
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
Reference: RBD-1365
Central point temperature measurement high/low temperature auto tracking real-time temperature display Alarm buzzer: >37.2ºC: high temperature audible alarm
Reference: RBD-1635
Logic control, 5V from Arduino main board Polarity protection for External motor power input 2 fast test buttons for each motor channel Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source) Up to 2A current each channel Pin 4, 5,6,7 are used to drive two DC motor Support PWM speed control Support advance speed control
Reference: RBD-1366
DT8380FC Infrared Thermometer Item no.: DT8380FC Temperature Range: -50~380°C/-58~716°F Measuring Accuracy: ±2% or 2C Distance Ratio: 12:1
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-1401
Measured variable Position Measuring principle Magneto-resistive Ambient temperature -40 °C ... 70 °C Repetition accuracy 0.2 mm Switching output PNP Switching element function N/O contact On time ≤1.3 ms Switch-off time ≤1.4 ms Max. switching frequency 150 Hz Max. output current 100 mA Max. output current in mounting kits 50 mA Max. switching capacity DC...
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-1561
4-20mA -50 - 150C WEIGHT: 350.00g DIMENSIONS: 4.00cm x 4.00cm x 1.50cm
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-1568
Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232) Transmission Speed: 300-115200 bps Working Modes: Asynchronous, half-duplex, differential transmission Transmission Media: Common wire, doule wire, UTP or Shielding Line Work Environment: -10°C to 85°C
Reference: RBD-2145
L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators
Reference: RBD-1653
Input Voltage: 88~264V/47~63Hz Output Voltage: 12V/4.2A DC Output Power: 50W
Reference: RBD-2158
Driver Chip: TB6560AHQ Operating Voltage: 10-35V Nominal Voltage: 24V With the large heat sink to ensure good heat dissipation 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
Reference: RBD-1675
Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0
Reference: RBD-2209
16 channels PWM servo motor driver controller board module Supports USB interface, TTL serial port, and Bluetooth communication Bluetooth communication can connect to Android phone or PC software Master chip STM32 series, frequency 48MHz Size 43.5x36mmx12mm, operating voltage 5V USB, TTL3.3V, servo motor supply 5-7.2V Channel 16, PWM accuracy 0.1ms
Reference: RBD-2308
This Dual Dc motor driver focuses on high efficiency and can withstand high current load, the maximum current up to 30A.
Reference: RBD-1684
8 Channel DC 12V Pro mini Relay Shield Module PLC Timer Board for Arduino
Reference: RBD-2111
DC Motor Speed Controller PWM 12V Controls the speed of a DC motor using Pulse-Width-Modulation (PWM) Provides continuous current of 3A to the motor or DC load Includes a 3A fuse for protection Supports reverse connection of power supply
Reference: RBD-1739
PT100 Temperature Transmitter 0-200 Celsius Range 4-20MA DC 24V
Reference: RBD-1816
Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v to 30VDC Compatible With Both 3V and 5V logic
Reference: RBD-2369
Built-in power switch High-performance CPU 16M high-capacity memory Built in Bluetooth 4.0 module Support TTL serial communication
Reference: RBD-1823
Power Supply: external micro USB-5V. Voltage Output: 0-12V. Current Output: 0-22mA. Multiple Display: just push the small button to switch the display mode
Reference: RBD-2389
This module is ideally suited to motor control to your project. This is the L298N Dual H-Bridge module which allows you to build in 2 controlled motors to your projects, controlling the speed with current. This can be used with a wide range of microcontrollers including Arduino and Raspberry Pi.
Reference: RBD-1824
Material: ABS Color: Yellow + Black Power: 2 x AAA Battery (NOT INCLUDED) Very Lightweight LED Light at tip for Dark sites
Reference: RBD-2390
Forward and reverse rotating :Forward and reverse rotating motor can be realized, can meet the needs of various working scenarios. Good production performance :Excellent production technology, not easy to cold joint, reliable and safe for you to use. Multiple good ability :With characteristics of strong driving ability, low heat dissipation and strong...