Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-2370
Module Properties: non-isolated Buck-Boost constant current, constant voltage module (CC-CV) charging module Battery charger (including ferroelectric), 4V, 6V, 12V, 14V, 24V battery charging, nickel-cadmium nickel-metal hydride batteries (battery) charger, solar panels, wind generators. Solar Panel, Wind generator voltage regulator, Car Power Supply
Reference: RBD-2460
LTC1871 DC-DC 3-35V To 3.5-35V Booster Step Up Module Converter Regulated Power 100W Buck-Boost Adjustable Supply LED VoltMeter
Reference: RBD-2831
Introducing a compatible Raspberry Pi Pico Clone, Made in China. Equipped with the authentic Raspberry Pi RP2040 microcontroller chip, this Pico offers comparable performance at a competitive price point. However, it's essential to note that while the microcontroller chip is genuine, the PCB itself is not manufactured by Raspberry Pi but rather in China....
Reference: RBD-0873
Passive PoE injector for outdoor radios, switches, and other network equipment Compatible with network devices that allow 48 Vdc passive PoE power Transmits power and data to remote devices up to 100 meters away
Reference: RBD-2887
The Development Kit based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Power your development in the fastest way combine with NodeMCU Firmware! R2 version had CP2102 USB-TTL instead, larger current support, slim board can put on breadboard. Programing it with Arduino IDE. High quality USB cable is needed for this board to give...
Reference: RBD-2711
Eco-friendly & Rechargeable Power: Replace disposable batteries with this eco-friendly 9V 280mAh Li-ion battery for your electronic devices. Long-lasting Performance: Enjoy repeated use without memory effect for reliable and sustainable power. Built-in Protection: Features short circuit and over-current protection for safe and dependable operation....
Reference: RBD-1530
Monomers Bearing: 30KG Permissible Load: 40KG M8 Thread
Reference: RBD-2798
Add another eight pins to your microcontroller using a MCP23008 port expander. The MCP23008 uses two I2C pins which can be shared with other I2C devices, and in exchange gives you eight general purpose pins. You can set each of eight pins to be input, output, or input with a pullup. There's even the ability to get an interrupt via an external pin when any...
Reference: RBD-2736
2×8 connector, easy with the MCU mount. Jumper selectable can work in parallel or serial mode. On board 3.3 V LDO 1117, provides 800 mA current. 5 V power supply is powered by the target board. 12 MHZ crystal.