Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0421
Compact and Portable pocket toolkit. RoboticsBD 44 different head style Rubber Shockproof gripped handle Strong and durable plastic Case Colour: Yellow-Light Green Interchangeable Precise Manual Tool Kit. High Strength Chrome Alloy is used to manufacture this tool. Magnetic bits are easy to fit into the handle. RoboticsBD Heat resistant.
Reference: RBD-0813
Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.
Reference: RBD-2234
¼ wave rubber duck antenna 860-960MHz communication center frequency of 915MHz RP-SMA connector Gain is 2dBi with an overall length of 110mm
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-0897
Durable and sturdy hardened mild steel construction Securely mounts 25GA 370 Series DC Gear Motor 1.6mm bracket thickness for enhanced strength 4.4mm bracket mounting slot size for versatile mounting options
Reference: RBD-1536
Over Charge Voltage Range: 4.25-4.35 V + 0.05 V Over Voltage Range: 2.5-3.0 V + 0.05 V Max. Operating Current: 13 A Max. Limiting Current: 20 A Charging Voltage: 8.4-9 V
Reference: RBD-1693
5PIN 12V 30A Power Relays SLA-12VDC-SL-A High Current Coil Power PCB Relay **Relay Brand can be different from the picture as per stock
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-1158
Width: 10 mm Length: About 33m. Type: Polyimide Tape. Heat Resistance: 200℃. Thickness Tolerance: ±10% . One-side Self-adhesive.
Reference: RBD-0568
Brand: Raspberry Pi Official
Fixed focus lens on-board Improved resolution – 8-Megapixel native resolution sensor-capable of 3280 x 2464 pixel static images Supports 1080p30, 720p60 and 640x480p90 video Size 25mm x 23mm x 9mm Weight just over 3g Connects to the Raspberry Pi board via a short ribbon cable (supplied) Camera v2 is supported in the latest version of Raspbian, Raspberry...
Reference: RBD-1190
Temperature Coefficient Type: NTC Thermal Time Constant: 10s Resistance 10kΩ Tolerance: ±1% Maximum Power Rating: 75mW Maximum Operating Temperature: +150°C Minimum Operating Temperature: -80°C Dimensions(dia.): 2 mm Length: 30mm Application: Compensation, Control, Measurement, etc.
Reference: RBD-2350
Waterproof Wireless Switch 433MHz Self-Powered Remote Control Switch Battery-Free Wall Light Switch
Reference: RBD-1820
38 Pin version 2.4GHz Dual-Mode WiFi + Bluetooth Development Board, 38PIN Ultra-Low power consumption works perfectly with the IDE A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and instead use the...
Reference: RBD-0409
No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting; RoboticsBD Note:...
Reference: RBD-0823
LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
Reference: RBD-2115
Toner transfer paper for DIY PCB Easily attach with Copper Board High quality Imported
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0878
Support Local Product. Made in Bangladesh. 2WD Robotics Wooden Chassis With Motors Wheels Laser-cut Gorjon-Plywood chassis with two dual shaft motors Simple mechanical structure with 2 DC gear motors Flexible turning and eco-friendly chassis Stable and easy to expand Made with 3mm Gorjon Ply Board You may find scratch marks due to handling and shipping....
Reference: RBD-0879
Support Local Product. Made in Bangladesh. 4WD Robotics Blue Chassis With Motors & Wheels Laser-cut Gorjon Plywood chassis with four dual shaft motors Simple mechanical structure with 4 DC gear motors Flexible turning and eco-friendly chassis Stable and easy to expand Made with 3mm Gorjon PlyBoard You may find scratch marks due to handling and...
Reference: RBD-0404
Brand: RoboticsBD
4 DOF Robotic Arm wooden DIY unassembled Premium quality kit with wood cutting parts and screws Includes 4 SG90 servos for joint motion Untrammeled and flexible motion with 4 degrees of freedom Product's color maybe different, local material is used. If any parts got broken during setup, please email us at ask@roboticsbd.com. We may not charge you for...
Reference: RBD-0881
6WD wooden smart robot chassis with motor Includes wooden chassis parts, 6 double shaft BO geared motors, 6 plastic wheels, nut-bolts, 2 wires, and 2 switches Chassis size: 20x14.2cm Wheel diameter: 4.8cm BO motor voltage: 3-9v DC BO motor speed: 150RPM
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,2.3A. আমরা আমাদের টেস্ট এ 5V, 1.7Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই...
Reference: RBD-2550
Simultaneous monitoring of PM2.5, CO2, TVOC, HCHO, AQI, temperature, and humidity. 2.8-inch TFT color display for clear detection data. Connects to Tuya App for real-time monitoring and historical data analysis. Portable size for easy desk placement and portability. Equipped with high-precision VOC sensors and low power consumption. PM2.5 Sensor: This...
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-1065
Latest Arduino CNC Shield Version 3.10 GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) Coolant enable Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping ) Compact design. 4-Axis support (X, Y, Z, A-Can duplicate...
Reference: RBD-1328
Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-1736
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm