Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1103
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....
Reference: RBD-1104
Isp interface: 6 PIN Isp interface: 10 PIN Power supply options: USB power Power supply options: external power supply (remove jumper cap)
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-0742
Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
Reference: RBD-1678
2A phase 3D Printer Big Easy Driver board V1.2 A4988 stepper motor driver board Module
Reference: RBD-2315
Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm
Reference: RBD-2145
L298P based Arduino motor driver shield Onboard Buzzer (D4). Onboard Bluetooth interface, you can directly plug, no wiring required. Six Analog interface. Forward, Backward steering indicators
Reference: RBD-2158
Driver Chip: TB6560AHQ Operating Voltage: 10-35V Nominal Voltage: 24V With the large heat sink to ensure good heat dissipation 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
Reference: RBD-2111
DC Motor Speed Controller PWM 12V Controls the speed of a DC motor using Pulse-Width-Modulation (PWM) Provides continuous current of 3A to the motor or DC load Includes a 3A fuse for protection Supports reverse connection of power supply
Reference: RBD-2419
Input Current: 0~5A Output Current: 0.5~4.0A Control Signal: 3.3~24V Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Temperature: -10~45℃ H bridge bipolar constant current drive.
Reference: RBD-2682
Double H bridge, which can drive two DC motors at the same time, single 7A current, high power; Wide voltage input 6.5V ~ 27V ; Signal optocoupler isolated input, can be directly controlled by IO port, free from interference; Undervoltage protection to prevent instantaneous high current burning of the module; High-power TVS and electrostatic bleeder...
Reference: RBD-3000
PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...
Reference: RBD-2754
The L298N 4WD Motor Driver is a versatile and robust H-bridge driver module designed for controlling DC motors with ease and precision. With its compatibility with 3.3V microcontrollers and support for popular platforms like Arduino and STM32, this module offers flexibility and convenience in motor control applications.